Hangar 9 Christen Eagle II 90 ARF Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 36

background image

27

Hangar 9 Christen Eagle II 90 ARF



15. Mount the spinner and propeller. Use open-end or

box wrenches to tighten the propeller nut. Check the fit of

the spinner to the propeller,. It may be necessary to trim the

opening for the propeller. The propeller must not contact

the spinner cone when it is installed. The spinner is held in

position using two M3 x 12 self-tapping screws. Tighten the

screws using a #1 Phillips screwdriver.

Wing Installation

Required Parts (all)

Fuselage assembly

Aluminum wing tube, 420mm

M3 washer (3)

Aluminum wing tube, 370mm

Interplane strut (2)

M3 x 45 machine screw (4)

M3 nut (4)
2.6mm x 16mm aluminum pin (8)
3mm x 270mm threaded rod
Metal clevis with silicone tubing (4)
M3 x 10 socket head machine screw (3)
Wing transport frame with rubber bands (2)
Bottom wing panel (right and left)
Top wing panel (right and left)



1. Locate the items for this section of the manual.



2. Insert two 2.6mm x 16mm aluminum pins in the

bottom of the interplane strut. Use a very small amount of

medium CA to secure the pins. Make sure the CA has fully

cured before proceeding.



3. Attach the wing strut to the top of the bottom wing

panel using an M3 x 45 machine screw. Use a #1 Phillips

screwdriver to tighten the screw.



4. Repeat steps 2 and 3 to prepare the remaining wing

panel for installation.



5. Slide the 420mm aluminum tube into the bottom wing

panel. The tube socket has a cap on it, so do not force the

tube in any farther than it will easily slide.

«
...
25
26
27
28
29
...
»

Содержание Christen Eagle II 90 ARF





































Отзывы:

Нет отзывов

Похожие инструкции для Christen Eagle II 90 ARF

Бренд: Badger Basket Страницы: 4

P-47 Thunderbolt

Бренд: Jamara Страницы: 12

Бренд: Park Pilots Страницы: 12

Бренд: E-FLITE Страницы: 40

Alphabert s Pen Pal Phonics

Бренд: VTech Страницы: 16

Fordhampton Garden center

Бренд: GAUGEMASTER Страницы: 4

P-3 Orion self adhesive

Бренд: Eduard Страницы: 3

Бренд: Makeblock Страницы: 3

C.P. Royal Hudson Live Steam - Alcohol Fired

Бренд: Accucraft trains Страницы: 6

Бренд: PARKZONE Страницы: 12

2551W Great NorthernFreight

Бренд: Lionel Страницы: 36

GeoTrax Rail & Road System J9525

Бренд: Fisher-Price Страницы: 2

Poopsie Sparkly Critters

Бренд: MGA Entertainment Страницы: 2

NH92022 CESSNA SKYHAWK

Бренд: NINCOAIR Страницы: 14

A-7D/E Corsair II

Бренд: Jet Hangar Страницы: 66

Бренд: LEXIBOOK Страницы: 1

Бренд: Eduard Страницы: 2

Бренд: PLAYTIVE JUNIOR Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды