HandTop HT3200-UV K Series Скачать руководство пользователя страница 55

Страница: 55 / 113

1. Ink supply system status: The green light means normal

status; yellow light means abnormal status. For different

colors, the status information will be shown.

2. Reset button: Reset function for external device control

board, equal as reboot the external device control

board. It will erase the warning information. Including

ink supply, air supply and light curtain reset.

1. Disable the solenoid valve of subtank

2. Time setting of priming ink

3. Prime selection

5.2.5 GUI control---LED ON/OFF setting

The adjusting password of the shutter (LED light source) opening and closing position

ua13

. After input, click verification to enable the fine tuning setting function.

The 8 parameters on the left are fine-tuning parameters in millimeters. The

parameters are described in detail as follows:

Left light on position adjustment (mm) of the left light when the car moves to the

right and left light off position adjustment when the car moves to the right (mm) :

According to the figure below, the top right arrow indicates that the car is moving to

the right, and the black solid rectangle on the left side of the car indicates the left

curing light. The vertical line i1 represents the position where the UV curing lamp is

turned on, while the vertical line i2 represents the position where the UV curing lamp

Содержание HT3200-UV K Series


















































































































Результаты поиска

Содержание HT3200-UV K Series

Отзывы:

Похожие инструкции для HT3200-UV K Series

Бренды по названию

Популярные бренды

HandTop HT3200-UV K Series, Инструкция по установке

Результаты поиска

Содержание HT3200-UV K Series

Отзывы:

Похожие инструкции для HT3200-UV K Series

Бренды по названию

Популярные бренды