Hamworthy F175V, Инструкция по установке, вводу в эксплуатацию и эксплуатации

Страница: 53 / 68

HAMWORTHY HEATING LTD
47
FLEET V series 500001217/D
APPENDIX C - FLUE DATA - Natural Gas
C1.0 FLUE SYSTEM
1. Detailed recommendations for flue systems are given in BS 6644, and IGE/UP/10. All flue discharges for plant
exceeding 150kW output must comply with the third edition of the 1956 Clean Air Act Memorandum.
WARNING: THE FLUE DISCHARGE FROM A FLEET BOILER WILL GENERATE A PLUME
AT THE TERMINAL EXIT. THIS MUST BE CONSIDERED WITH REGARD TO TERMINAL
LOCATION AND ADJACENT BUILDING FABRIC.
FOR B23 INSTALLATIONS THE HAMWORTHY AIR INLET FILTER MUST BE USED
C1.1 General Requirements
The Fleet boilers are designed to be used with natural draught or room sealed flues. Flue systems should be
designed in accordance with regulations and with reference to BS 6644 and IGE/UP/10.
The following points should be noted:
a. Due to the high thermal efficiency of the boiler, condensation will occur in the flue. It is strongly recommended
that the design of the flue system recognises this. HHL supply plastic flue components and suitable terminals to
discharge the flue gases safely. The Fleet flue systems supplied by Hamworthy are non UV stabilised polypropylene
and are therefore suitable for internal use only. For external flue runs and termination, either use the dedicated kits
supplied by Hamworthy or refer to a chimney specialist .
b. Care should be taken to ensure that the flue is installed such that any condensation is continuously drained.
Any flue system with a horizontal section should have a maximum slope of 3° upwards in the direction of the
exhaust gas flow. All joints should be such that any condensation is directed back down the slope to an open
drain connection in the flue. The drain pipe must be manufactured from a corrosion resistant material and at least
15mm diameter. It must have a fall of at least 3° (approx. 50mm/meter) and connect to a drain via a waste trap.
c. Boiler flue outlet sizes - A flue system designed with the same diameter as the boiler flue outlet may not provide
satisfactory performance in all applications. Consideration must be given to the correct calculation of the required
flue size. If in any doubt consult Hamworthy Heating Ltd who can supply a full flue design and installation service.
C1.2 Waste Gas Volume and Temperature.
It is recommended that the volume and temperature of the waste gases used for design of the flue system are as
given in the above tables.
* Note:- Flue gas volumes are corrected to a flue gas temperature of 15°C and barometric pressure of
1013.25mbar.
FLUE DATA per boiler module BOILER MODEL
F175V
F200V
F250V
Flue connections (concentric) - mm 130/200, 150/220
Flue /Air connections (twin duct) - mm 130/100
Flue connection (B23 open flue) - mm 130
Approx. Flue Gas Temperature @ 80/60°C - °C (Gross) 60
Approx. Flue Gas Temperature @ 50/30°C - °C (Gross) 40
Pressure at the boiler flue outlet - Pa/mbar
150 150 150
Approx. Flue Gas Volume @ 9.2% CO
2
- m
3
/h*
225 260 325
F300V
F350V
Flue connections (concentric C33) - mm 150/220
Flue /Air connections (twin duct C53) - mm 150/100
Flue connection (B23 open flue) - mm 130
Approx. Flue Gas Temperature @ 80/60°C - °C (Gross) 60
Approx. Flue Gas Temperature @ 50/30°C - °C (Gross) 40
Pressure at the boiler flue outlet - Pa/mbar
150 150
Approx. Flue Gas Volume @ 9.2% CO
2
- m
3
/h* 390 450