HAMPTON BAY H35U-NG Скачать руководство пользователя страница 6

Страница: 6 / 60

Hampton® H35U Direct Vent Freestanding Gas Stove

safety label

This  is  a  copy  of  the  label  that  accompanies
each  Direct Vent Freestanding Gas Stove. We
have  printed  a  copy  of  the  contents  here  for
your review.

NOTE: Hampton

units are constantly being

improved. Check the label on the unit and if
there is a difference, the label on the unit is
the correct one.

Copy of Safety Label

920-414

560

H35U-NG

H35U-LP

C# 4001172

APPAREIL FONCTIONNANT AU GAZ PROPANE

APPAREIL FONCTIONNANT AU GAZ NATUREL

Listed:

VENTED GAS FIREPLACE HEATER /

FOYER AU GAZ À ÉVACUATION

Certified to /Certifié : ANSI Z21.88-2019

MAY BE INSTALLED IN MANUFACTURED (MOBILE) HOMES

AFTER FIRST SALE

Refer to Intertek’s Directory of Building Products for detailed information.

Pour plus de détails, se reporter au Répertoire des produits de construction de Intertek.

3.5

0.87

1.6

0.40

30,000

21,500

(8.78 Kw/h)

(6.30 Kw/h)

Model/Modèle :

Pression d’alimentation minimale

Pression manifold élevée

Pression manifold basse

Débit calorifique maximal

Débit calorifique minimal

Taille de l’orifice

Altitude

Pression d’alimentation minimale

Pression manifold élevée

Pression manifold basse

Débit calorifique maximal

Débit calorifique minimal

Taille de l’orifice

Altitude

2.74

WC/C.E.

2.49

6.4

1.59

29,500

(8.64 Kw/h)

24,000

7.03

Model/Modèle :

ÉLECTRICAL SUPPLY/ALIMENTATION ÉLECTRIQUE : 115V_60HZ less than/moins de 2 A.

For Use Only with Barrier (Part #743-100). Follow Installation Instructions.

Utiliser uniquement avec un écran de sécurité (pièce n 743-100). Suivre les consignes d’installation.

NOT FOR USE WITH SOLID FUELS / NE PAS UTILISER AVEC UN COMBUSTIBLE SOLIDE

FPI Fireplace Products International Ltd. Delta, BC, Canada

Made in Canada / Fabriqué au Canada

utilisé

For the State of Massachusetts, installation and repair must be done by a plumber or gasfitter licensed in the Commonwealth of
Massachusetts.

For the State of Massachusetts, flexible connectors shall not exceed 36 inches in length.

For the State of Massachusetts, the appliances individual manual shut-off must be a t-handle type valve.

The State of Massachusetts requires the installation of a carbon monoxide alarm in accordance with NFPA 720 and a CO alarm with

battery back up in the same room where the gas appliance is installed.

Содержание H35U-NG





























































Результаты поиска

Содержание H35U-NG

Отзывы:

Похожие инструкции для H35U-NG

Бренды по названию

Популярные бренды

HAMPTON BAY H35U-NG, Инструкция для владельца и по установке

Результаты поиска

Содержание H35U-NG

Отзывы:

Похожие инструкции для H35U-NG

Бренды по названию

Популярные бренды