manualshive.com logo in svg

HAMPTON BAY H35U-NG, Инструкция для владельца и по установке

Поделиться
Скачать
HAMPTON BAY H35U-NG Скачать руководство пользователя страница 20

20

Hampton® H35U Direct Vent Freestanding Gas Stove

installation

Offset to Vertical Terminations

Venting Arrangements

Vertical Terminations Systems for Residential Manufactured and Mobile 
Homes

The shaded area in the diagram below shows all allowable combinations of straight vertical and 
offset to vertical runs with vertical terminations.

 

Maximum two 45

o

 elbows

.

If the vent is ENCLOSED in a chase (min. size 9" x 9") maintain a 1-1/4" clearance to combustibles.

May be installed in Manufactured (Mobile) Homes after first sale.

Horizontal Terminations for All 
Venting Systems

The shaded areas in the diagram below show 
all allowable combinations of vertical runs 
with horizontal terminations. Maximum one 90

O

 

elbow (two  45

o 

elbows equal one 90

o

 elbow). 

All approved caps listed on page 12 - may be 
used.

Propane and Natural Gas: 
Residential, Manufactured and 
Mobile Home Installations

The  venting  arrangements  diagrammed  below, 
have a min. of 75% (flue loss) efficiency with Fan 
Off, as required for manufactured homes. (Actual 
efficiency may be as high as 85%)

May be installed in manufactured (mobile) 

homes after first sale.

Rotating 45

o

 Elbow for Straight Horizontal Terminations

1)

 Remove the 4 screws of the top panel.

2) 

Remove all 4 screws that secure the elbow to 

the unit using a 1/4" magnetic nut driver.

NOTE: See "Vent Restrictor Position" sec-
tion for installation instructions for the Vent 
Restrictor Position.

3)

 Rotate the elbow 180

o 

4) 

Secure the elbow by securing it with the 4 screws. 

5)

 Return top panel. Secure with the four screws. 

See figure 1.

Figure 1

Figure 2

Figure 3

Содержание H35U-NG





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды