manualshive.com logo in svg

HAMPTON BAY H35U-NG, Инструкция для владельца и по установке

Поделиться
Скачать
HAMPTON BAY H35U-NG Скачать руководство пользователя страница 46

46

Hampton® H35U Direct Vent Freestanding Gas Stove

maintenance

H35U-NG / LP AND H35S-NG / LP

2

920-450

10.20.21

WARNING: Electrical Grounding Instructions

This appliance is equipped with a three pronged (grounding) plug for 
your protection against shock hazard and should be plugged directly 
into a properly grounded three-prong receptacle. Do not cut or remove 
the grounding prong from this plug.

Removing the Fan

1.  Unplug or disconnect power source to stove.

2.  Reverse  steps  7  to  10  from  “Installing  the  Optional  Fan”  instructions 

above.

Servicing the Thermodisc

To replace or service the fan thermodisc (temperature switch), use the 
following steps:

1. Unplug or disconnect power source to stove.
2. Remove two screws from the lower left and lower right areas of the 

back cover panel.

3. Lift the back cover panel up and pivot out away from the 

unit. Take  care  note  to  pull  on  the  wires  attached  to  the 
back cover panel.

NOTE:

  When  servicing  the  thermodisc  ensure  you  do  not 

damage the air intake flex tubes.

Figure 11

Figure 12

4.The thermodisc can now be accessed on the back of the 

firebox behind the air intake tube. (Image 14)

Figure 13

Figure 14

Figure 9

Figure 10

Fan Maintenance

Figure 1

Figure 2

Figure 3

Figure 4

Содержание H35U-NG





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды