Halcro DM10 Скачать руководство пользователя страница 23

Страница: 23 / 29

Page 23 of 29

dm10

SPECIFICATIONS & FEATURES of the

HALCRO dm10

Remote Control Preamplifier

Inputs

3 RCA Unbalanced Voltage Mode

3 XLR Balanced Voltage Mode

1 RCA Current Mode

Any 5 of the above I/Ps are user
programmable to respond to the device

names; CD, DVD, Tape, Tuner, Aux1

1 RCA Unbalanced Phono

1 XLR Balanced Phono

Moving Coil or Moving Magnet

Cartridge

Variable

Phono

capacitance

and

resistance knobs

Outputs

2 Pair RCA Unbalanced Voltage Mode,

Bridgeable

2 Pair XLR Balanced Voltage Mode,

Bridgeable

2 Pair RCA Current Mode: 1 pair for un-

bridged connection, the other pair used
in bridged mode

1 Pair RCA Tape output

¼ inch Stereo Headphone Jack

6-pin XLR power ON/OFF, pulsed and

level output control

Power supply

Switch-mode, >200kHz CW, 4th order mains
filter, 4th order supply rail filter. Fully

complies with EMC and CE standards.
Circuit contains extensive mains transient

protection and fault sensing protection.

Power consumption.

100W max via IEC input

Mains voltage.

85VAC to 240VAC at 40Hz to 200Hz or
120V to 340V D.C.
(Power supply will operate up to 270V but

IEC sockets only rated up to 240V by
regulatory authorities.)

Remote Control: 3 x AAA batteries

(supplied)

Dimensions

Width: 448mm, 17.64 inches

Depth: 400mm, 15.74 inches

Height: 240mm, 9.44 inches

Weight: 23kg, 49.6lbs

Shipping Dimensions

- Timber case

Width: 585mm, 23 inches

Depth: 535mm, 21 inches

Height: 515mm, 20 inches

Weight: 36 kg, 79 lbs

Remote Control dimensions

Length: 183mm, 7.2 inches

Width: 50mm, 1.96 inches

Thickness: 24mm, .94 inches

Weight: 280gm, .6 lbs

Gain

Un-balanced and balanced +20dB to -60dB
set by volume control.

Phono 32dB, 38dB or 44dB for moving coil,
switch selectable

+27dB for moving magnet (measured at
1kHz)

Input impedance

Balanced; 10kohm
Un-balanced; 10kohm

Moving magnet; 10kohm to 60kohm plus
60pF through to 350pF both continuously

variable
Moving coil; 220ohm plus 4.7nF

Current input mode; 50ohm

Output impedance

170 + 170ohms balanced and 170ohms
un-balanced

>30kohms current mode
10ohms headphones
340ohms tape

Distortion

Unmeasurable: below noise floor

At full specified output, < 250 parts per
billion (-132dB) for balanced and un-

balanced and current modes

Volume control

+20dB to –60dB in 0.5dB steps.

Phono equalization

Conforms to /-0.5dB of the RIAA
standard.

Содержание DM10






























Результаты поиска

Содержание DM10

Отзывы:

Похожие инструкции для DM10

Бренды по названию

Популярные бренды

Halcro DM10, Руководство пользователя

Результаты поиска

Содержание DM10

Отзывы:

Похожие инструкции для DM10

Бренды по названию

Популярные бренды