background image

¤

SOLDERING STATION

Instruction Manual

Thank you for purchasing the HAKKO 937 soldering station.

Please read this manual before operating the HAKKO 937.

Keep this manual readily accessible for reference.

 CAUTION

When seeking tip replacements, select only “Hakko” genuine soldering iron tips

that are intended for your particular model of soldering iron (Please refer to the

instruction manual). If an incompatible tip or a tip made by another manufacturer

is used, the original performance of the soldering iron may not be obtained.

Furthermore, the heating element, P.W.B. and transformer may be damaged.

TABLE OF CONTENTS

1. PACKING LIST ........................................................................... 1
2. SPECIFICATIONS ...................................................................... 1
3. WARNINGS AND CAUTIONS .................................................... 2
4. PART NAMES ............................................................................. 3
5. SETTING UP & OPERATING THE HAKKO 937 ........................ 3
6. PARAMETERS ........................................................................... 6
7. CALIBRATION OF IRON TEMPERATURE ................................ 7
8. CALIBRATION CHART .............................................................. 8
9. TIP CARE AND USE .................................................................. 9

10. MAINTENANCE ......................................................................... 9
11. TIP STYLES .............................................................................. 10
12. ERROR MESSAGES ................................................................ 11
13. TROUBLESHOOTING GUIDE .................................................. 12
14. CHECKING FOR BREAKAGE OF THE HEATING ELEMENT AND CORD ASSEMBLY . 14
15. PARTS LIST 
(Station/Iron Holder) ............................................ 16

(Iron) .................................................................... 17

16. WIRING DIAGRAM ................................................................... 18

Содержание 937





















Отзывы: