Haier HDY-E60 страница 14 Скачать руководство пользователя

Страница: 14 / 16

INSTALLATION INSTRUCTIONS

Rear venting

If you want to choose the rear venting mode, the exhaust grill at the front of the dryer

needs to be replaced with the outlet cover from the back panel of the dryer. Gently

open the grill, using a thin tool such as a key. Next, remove the cover from the

back panel and clip it into the grill space at the front panel. The exhaust grill is not

required when using a flexible hose.

INSTALL THE FLEXIBLE HOSE

(

optional

Flexible hose)

Duct hole

Outdoor

Flexible hose

Flexible connector

Flexible hose clip

Connect the narrow end of the

connector to the dryer duct pipe mouth

at the back of the dryer. Then connect

the flexible hose to the wide end of

the connector. Use the clip to

fasten connection point between the

flexible hose and connector (fasten clip

with a screwdriver). Extend the flexible

hose through the duct hole, make

sure the flexible hose is not twisted to

allow the air to be vented outside.
Notes: If duct hole is not available at user's home, make sure the flexible hose

is vented through a window.

If the dryer is mounted on the wall in the inverted position, you can not use the

flexible hose.

Correct fixing mode:

Fig.1

Fig.2

Fig.3

(

diameter

＞

100mm)

The flexible hose should be angled to avoid water running back into the dryer.

Ensure a vent cap is fitted when vented outside.

Vent cap

Extra Dry

100min

30min

60min

30min

Содержание HDY-E60

















Результаты поиска

Содержание HDY-E60

Отзывы:

Похожие инструкции для HDY-E60

Бренды по названию

Популярные бренды

Haier HDY-E60, Руководство пользователя

Результаты поиска

Содержание HDY-E60

Отзывы:

Похожие инструкции для HDY-E60

Бренды по названию

Популярные бренды