Haier GE GDF510P M4 Series Скачать руководство пользователя страница 33

Страница: 33 / 79

– 33 –

The pocket handle is attached to the inner

door panel. The front control console must

be removed as previously described in

Front

Control Console Removal

(in this section).

Remove six 1/4-inch hex-head screws.

The pocket handle is clipped to the plastic inner

door and on the adapter of the stainless steel

(SS) inner doors.

Model GDP615H features a new pocket handle

design and has top controls.

The new pocket handle is attached to the outer

door panel with seven 1/4-inch hex-head screws.

To remove the handle, remove and separate the

door. Remove seven 1/4-inch hex-head screws.

The handle can be removed toward the inside of

the panel.

Pocket Handle (Front Control Only)

Pocket Handle (GDP615)

Содержание GE GDF510P M4 Series
















































































Результаты поиска

Содержание GE GDF510P M4 Series

Отзывы:

Похожие инструкции для GE GDF510P M4 Series

Бренды по названию

Популярные бренды

Haier GE GDF510P M4 Series, Руководство по обслуживанию

Результаты поиска

Содержание GE GDF510P M4 Series

Отзывы:

Похожие инструкции для GE GDF510P M4 Series

Бренды по названию

Популярные бренды