Haier GE GDF510P M4 Series Скачать руководство пользователя страница 35

Страница: 35 / 79

– 35 –

5. The light pipe separates from the bottom

cover with tabs. A small screw-driver may be

needed to start the first tab.

The light pipe may be flexed by twisting to

release the remaining tabs (four each side).

7. With the light pipe removed, the UI may be

lifted out of the bottom cover.

• When replacing User Interface (UI) control

boards, the new UI board must be configured

as per instructions included with the

replacement. If the personality is not set by

using the four jumpers, the buttons, LED’s or

cycles will not function properly.

•

Diagnostics for both front and top control UI’s

are found in the

Electronic Control

section

of this service guide.

Top Control Console Cover Removal

1. Remove and separate the door.

2. Remove the bottom cover, User Interface (UI),

light pipe and buttons.

3. Remove the top console and cover as an

assembly. There are six 1/4-inch hex-head

screws, securing the assembly to the inner

door (note the length of the screws). A new

cover should be replaced in the event the

cover is loose or must be removed. The tabs

are likely to break on removal.

Installing a New Top Cover

1. The top cover is secured with sixteen tabs,

and the console has cutouts or slots to allow

the top cover to click lock together.

2. Position the tabs on the cover into the slots

on the console.

3. Press the top and console securely together

and slide the parts to engage the tabs into the

slots. Start from one end and work across to

the other end. A series of five audible clicks

will be heard as the cover and console snap

together.

Six 1/4-in. hex-

head screws

Top Control Console Cover

Содержание GE GDF510P M4 Series
















































































Результаты поиска

Содержание GE GDF510P M4 Series

Отзывы:

Похожие инструкции для GE GDF510P M4 Series

Бренды по названию

Популярные бренды

Haier GE GDF510P M4 Series, Руководство по обслуживанию

Результаты поиска

Содержание GE GDF510P M4 Series

Отзывы:

Похожие инструкции для GE GDF510P M4 Series

Бренды по названию

Популярные бренды