Haier GE GDF510P M4 Series Скачать руководство пользователя страница 75

Страница: 75 / 79

– 75 –

4. The vent conduit, fan and the duct are

removed as an assembly.

Operation

Heater operation is the same as the passive

system. The fan is a brushless motor and

operated by 13.5 VDC and runs at 6,000 RPM.

There are no consistent resistance readings to

make a viable ohm check. A power dry cycle is

50 minutes, then the Clean light comes on. If the

consumer does not open the door, the fan will

run an extra 90 minutes before shutting off. If

the consumer opens the door, the fan will shut

off and not restart should the door be closed and

latched.

Diagnostics

The door will have to be removed and separated.

The door can be plugged back in and put into

service mode to make voltage checks. 12 to 14

VDC can be checked at the UI board, connector

J102 (2-pin connector) from

red

black

Venting / Airflow

To remove the vent, the door must be removed

and separated (see

Door

under the

Tub and

Structure

section of this guide).

Fan Assist Venting

(on some models)

A fan assembly is located in the door.

Components include a 13.5 VDC fan and ducting

to the bottom of the door. The power dry system

must be removed to access the door control

components. Operation, specifications and

diagnostics will be covered in the

Dry System

section of this service guide.

Power Dry System Removal

1. Remove the inner door vent cover.

2. Disconnect the wire harness from the fan to

the User Interface (UI) control.

3. Remove the 1/4-inch hex-head screw.

Mounting Screw

Vent Duct and Fan

Gasket

Vent Cover

Conduit

Fan (Inside Duct)

Duct

Содержание GE GDF510P M4 Series
















































































Результаты поиска

Содержание GE GDF510P M4 Series

Отзывы:

Похожие инструкции для GE GDF510P M4 Series

Бренды по названию

Популярные бренды

Haier GE GDF510P M4 Series, Руководство по обслуживанию

Результаты поиска

Содержание GE GDF510P M4 Series

Отзывы:

Похожие инструкции для GE GDF510P M4 Series

Бренды по названию

Популярные бренды