Haier GE GDF510P M4 Series Скачать руководство пользователя страница 27

Страница: 27 / 79

– 27 –

Lower Rack

Several lower racks are available with different

tine configurations; consult the Owner’s Manual

for details on the lower racks.

The lower rack roller assemblies consist of

brackets, rollers, and covers (left or right, two per

side) as well as rollers (four per side).

To remove the lower rack rollers, lift up on the

cover (shaded grey in the image below) to

release; then pull out on the cover to unclip the

center tabs.

The rollers will slide off the bracket and the

bracket (shaded grey in the image below) is

pushed to the rear of the rack to remove.

Bracket

Rollers

Cover

Tabs in center

Left Side

Right Side

The left and right brackets and covers are

different part numbers and are marked "L" or

"R" (left or right) on the inside to insure proper

installation.

Содержание GE GDF510P M4 Series
















































































Результаты поиска

Содержание GE GDF510P M4 Series

Отзывы:

Похожие инструкции для GE GDF510P M4 Series

Бренды по названию

Популярные бренды

Haier GE GDF510P M4 Series, Руководство по обслуживанию

Результаты поиска

Содержание GE GDF510P M4 Series

Отзывы:

Похожие инструкции для GE GDF510P M4 Series

Бренды по названию

Популярные бренды