Haier 2HUM18HC003, Руководство по эксплуатации

Страница: 4 / 22

Operation
Air Flow Direction Adjustment
Press FAN button. For each press, fan speed
follows:
Remote controller:
Press button
Every time the button is pressed, temp.setting
increase 1
o
C / 2 F, if kept depressed, it will
increase rapidly
Every time the button is pressed, temp.setting
decrease 1
o
C / 2 F, if kept depressed, it will
decrease rapidly
Select a desired temperature.
4.Fan speed selection
3.Select temp.setting
The air conditioner will be running at the speed shown
in the display.
When FAN is set to AUTO, the air conditioner
automatically adjusts the fan speed according to room
temperature.
1. Unit start
Press ON/OFF on the remote controller, unit starts.
Basic Operation
Remote controller
1.Status display of air flow
When restarting the unit after it has been turned off,
the unit will keep the swing position before it stops
working.
2.Left and right air flow adjustment(manual)
Cautions:
When adjusting the louver by hand,turn off the unit.
When humidity is high,condensate water might occur
adjusted to left or
It is advisable not to keep horizontal louver at
downward position for a long time in COOL or DRY
mode ,otherwise, condensate water might occur.
Emergency Operation and Test Operation
at air outlet if all vertical louvers are
right.
Note:
changes as
Operation
Mode
Remote
Controller
Note
In DRY mode , when room temperature is 2 C/4 F degrees
o
less than the temperature set point, the unit will run
intermittently at LOW speed regardless of FAN setting.
Under the mode of auto operation, air conditioner will
automatically select Cool or Heat operation according to
room temperature. When FAN is set to AUTO the air
conditioner automatically adjusts the fan speed according
to room temperature.
In FAN operation mode , the unit will not operate in COOL or
HEAT mode but only in FAN mode, AUTO is not available in
FAN mode. And temp. setting is disabled. In FAN mode,
sleep operation is not available.
Emergency Operation:
Use this operation only when the remote controller is defective
or lost, and with function of emergency running, air conditoner
can run automatically in few seconds.
When power switch is turned on for the first time and
emergency operation starts, the unit will run automatically in
the following modes:
Room
temperature
Designated
temperature
Timer
mode
Fan
speed
Operation
mode
Above 23
ą
/73
ȯ
26
ą
/ 79
ȯ
Below 23
ą
/73
ȯ
23
ą
/ 73
ȯ
No
AUTO
AUTO
COOL
HEAT
No
During emergency operation it is impossible to change the
settings of temp. and fan speed,It is also not possible to
operate in Timer or Dry mode.
the room
temperature is below 16
ą
/ 60
ȯ
,
Test Operation:
Use this switch in the test operation when
do not use it in the normal operation.
Test ope ration switch is the same as emergency switch.
Under this operation mode,the fan motor of indoor
unit will run in high speed.
LOW MED HI
COOL/DRY:
HEAT:
Initial state
AUTO
2. Select operation mode
COOL button:Cooling mode
HEAT button: Heating mode
DRY button: Dehumidify mode
Beep
DRY
COOL
AUTO
HEAT
FAN
In HEAT mode, warm air will blow out after a short
period of the time due to cold-draft prevention function.
When FAN is set to AUTO, the air conditioner automatically
adjusts the fan speed according to room temperature.
2
When the emergency operation switch is pressed, the unit
beeps once, which starts the operation.
from the switch: the cooling operation
Continue to press the test operation
switch for more than 5 seconds.After
you hear two beeps, release your finger
starts with the air flow speed "HI".
Move the vertical louver by a knob on air
to adjust left and right direction to achieve
stereoscopic air flow as the figure below.
conditioner
o
o
A
U
T
O
o
Beep-Beep
stereoscopic air flow