C
=
Gemma warning light key.
• Replacing the halogen/incandescent lamps (Fig.8):
Only use lamps of the same type and wattage installed on
the device.
• Commands slider (Fig.9) the key symbols are explained
below:
This hood is fitted with a
microswitch
which allows the
activation of the motor speed) through the opening of the
telescopic undercarriage. If the telescopic undercarriage is
closed the motor speeds cannot be activated. This microswitch
does not have an impact on the activation of the lights which
must be switched on through the appropriate switch (see
Fig.9A).
A
=
Light switch
A1
=
Off key
A2
=
On key
B
=
Speed control
B1
=
FIRST SPEED key
B2
=
SECOND SPEED key
B3
=
THIRD SPEED key.
Warning!
If the telescopic undercarriage is closed with
the speed set at 2, once it is re-opened, the hood will be
reactivated with the same speed in use when the hood was
closed.
• Commands (Fig.10):
Push-button A =
On/off lights switch.
Push-button B =
On/off cooker hood switch. The appliance
switches on at speed level 1, If the cooker hood is on depress
the push-button for 2 sec. to switch off the cooker hood. If
the cooker hood is at speed level 1 it will not be necessary
to depress the push-button to switch the cooker hood off.
Decreases the motor speed.
Display C =
Indicates the motor speed level selected and
activates the timer.
Push-button D =
Switches on the cooker hood. Increases the
motor speed. Touching the key at 3rd speed, the intensive
function runs for 10’, then the appliance go back to work at
the original speed. During this function the display blinks.
Key E =
The Timer times the functions on activation for
15 minutes, after which they are switched off. The Timer is
deactivated by re-pressing
Key E
. When the Timer is activated
the decimal point must flash on the display. The Timer cannot
be activated if the intensive speed is functioning.
The “
clean air
” function is activated by pressing key
E
for 2
seconds when the appliance is switched off. This switches
the motor on for 10 minutes every hour at the first speed.
During functioning a rotary movement of the peripheral
segments must be visualised on the display. When this time
has passed the motor switches off and the fixed letter “
C
” must
be visualised on the display until the motor re-starts after 50
minutes for another 10 minutes and so on. Press any key apart
from the light keys to return to normal functioning. Press key
E
to deactivate the function.
• Anti-grease/active charcoal filters saturation:
- When display item
C
flashes, at a speed where it alternates
with the letter
F
(e.g.
1
and
F
), the anti-grease filters must be
washed.
- When display item
C
flashes, at a speed where it alternates
with the letter
A
(e.g.
1
and
A
), the active carbon filters must
be replaced or washed depending on the type of filter.
After the clean filter has been positioned correctly, the
electronic memory must be reset by pressing button
A
for
approximately
5 seconds
, until the indication
F
or
A
shown
on the display
C
stops flashing.
• Commands luminous
(Fig.11)
the key symbols are
explained below:
A =
LIGHT
B =
OFF
C =
SPEED I
D =
SPEED II
E =
SPEED III
F =
AUTOMATIC STOP TIMER - 15 minutes
(*)
If your appliance has the
INTENSIVE
speed function, from
speed THREE, press key
E
for 2 seconds and it will be activated
for 10 minutes after which it will return to the previously
set speed. When the function is active the LED flashes. To
interrupt it before the 10 minutes have elapsed, press key
E
again. Some models allow activating this function even with
speed one and two.
By pressing key
F
for two seconds (with the hood switched
off) the “
clean air
” function is activated. This function switches
the appliance on for ten minutes every hour at the first speed.
As soon as this function is activated the motor starts up at the
first speed for ten minutes. During this time key
F
and key
C
must flash at the same time. After ten minutes the motor
switches off and the LED of key
F
remains switched on with
a fixed light until the motor starts up again at the first speed
after fifty minutes and keys
F
and
C
start to flash again for ten
minutes and so on. By pressing any key for the exclusion of
the hood light the hood will return immediately to its normal
functioning (e.g. if key
D
is pressed the “
clean air
” function is
deactivated and the motor moves to the 2nd speed straight
away. By pressing key
B
the function is deactivated).
(*)
The “
AUTOMATIC STOP TIMER
” delays stopping of the
hood, which will continue functioning for 15 minutes at the
operating speed set at the time this function is activated.
• Anti-grease/active charcoal filters saturation:
- When the
A
key flashes with a
2 second
frequency the anti-
grease filters must be washed.
- When the
A
key flashes with a
0.5 second
frequency the
active carbon filters must be replaced or washed depending
on the type of filter.
Once the clean filter has been put back one must reset the
electronic memory by pressing the
A
key for approximately
5 seconds
until it stops flashing.
THE MANUFACTURER DECLINES ALL RESPONSIBILITY
FOR EVENTUAL DAMAGES CAUSED BY BREACHING THE
ABOVE WARNINGS.
NEDERLANDS
NL
ALGEMEEN
Lees aandachtig de inhoud van deze handleiding. Hierin staan
belangrijke aanwijzingen voor een veilige installatie, gebruik
en onderhoud. Bewaar de handleiding om die later te kunnen
raadplegen. Het toestel werd ontworpen in een versie voor
afzuiging (evacuatie van de lucht naar buiten Afb.3A) en
voor filtering (recirculatie van de lucht binnen Afb.3B) of met
externe motor (Afb.3C).
- 17 -
Содержание 539-82-073
Страница 2: ... 2 ...
Страница 3: ... INCANDESCENT TUBOLAR LAMP Ø 25mm L85 E14 40W CANDLE HALOGEN LAMP Ø 35mm E14 28W 3 ...
Страница 24: ...3LIK1279 ...
