Haes AlarmSense Скачать руководство пользователя

Страница: 8 / 44

AlarmSense Installation, Commissioning & Operating Manual

Approved Document UI-ALS-01 Issue 2.0

ABOUT THIS PANEL

General Speci

cation

Enclosure

Steel IP30. Epoxy powder coated Interpon Radon, silver grey

Temperature range

-5 deg C to +40 deg C max RH 95%

Number of AlarmSense circuits

2 or 4

Device compatibility

Apollo: AlarmSense only

TECHNICAL SPECIFICATION

Electrical Speci

cation Inputs & Outputs - TPCA06-A2/A4

Cabling

Fire resistant screened cable, minimum
size 1mm

. Max cable length 1Km (20

Ohm). FireBurn, FP200 or equivalent
(max capacitance 1uF, max inductance 1
millihenry).

Suitable cable glands must be used.

Terminal capacity

0.5mm

to 2.5mm

solid or stranded wire.

PSU @ output

Power supply voltage control line.

For temperature compensation control.

PSU Input + -

28vdc supply input. Diode protected for
reversal and independent short circuit.
Max current 3 amps.

Max input current 3 amps. Input voltage
22vdc to 32vdc.

28v+, 0v- power output

28vdc supply output for

re alarm

accessory relays etc. Max continuous
use = 400mA.

Fused @ 500mA. Fuse = 500mA
resettable fuse.

Common

re relay

Fire relay contact. Clean C/O.
Max 3A @ 30vdc

Unfused

Common fault relay

Maintained fault relay contact. Clean
C/O. Max 3A @ 30vdc

Unfused

Outputs; FR, FLT

Switched -ve voltage outputs for relay
control.

Overload voltage protected to 52vdc.
Current limited 680R. Max load = 40mA

Inputs; CC, PUL

Switched -ve inputs, connect to 0v to
trigger. Max input voltage = 28vdc. Non
latching, max resistance 100R.

Protected via 10K Ohm impedance, 3v6
zener diode.

SNDR 1 - 2

28vdc polarity reversal monitored
sounder outputs to

re alarm devices.

3K3 Ohm 5% 0.25W EOL resistor.

Monitoring current limit 28mA, fused @
500mA. Typical max load 22 devices @
18mA each per circuit. Ensure 0.9A is not
exceeded.

Zone 1 - 4

AlarmSense

re alarm zone circuits.

3K3 Ohm 5% 0.25W EOL resistor.

Monitoring current limit 50mA, fused
@ 200mA. Typical max load 20 alarm
devices @ 18mA each per circuit. Ensure
0.2A is not exceeded.

www.acornfiresecurity.com

Содержание AlarmSense













































Результаты поиска

Содержание AlarmSense

Отзывы:

Похожие инструкции для AlarmSense

Бренды по названию

Популярные бренды

Haes AlarmSense, Инструкция по установке, пусконаладке и эксплуатации

Результаты поиска

Содержание AlarmSense

Отзывы:

Похожие инструкции для AlarmSense

Бренды по названию

Популярные бренды