manualshive.com logo in svg

Haes AlarmSense, Инструкция по установке, пусконаладке и эксплуатации, Страница: 4 / 44

Поделиться
Скачать
Haes AlarmSense Скачать руководство пользователя страница 4

AlarmSense Installation, Commissioning & Operating Manual

Approved Document UI-ALS-01 Issue 2.0

2

ABOUT THIS PANEL

PRODUCT OVERVIEW

The Haes AlarmSense is a 2 or 4 zone AlarmSense protocol control panel with integral power supply & 

The Haes AlarmSense is a 2 or 4 zone AlarmSense protocol control panel with integral power supply & 
space for standby batteries. 

space for standby batteries. 

Haes AlarmSense panels are fully approved to European standards EN54-2 & 4, Fire Detection and Alarm 

Haes AlarmSense panels are fully approved to European standards EN54-2 & 4, Fire Detection and Alarm 
Systems – Control & Indicating Equipment.

Systems – Control & Indicating Equipment.

The control panel comprises of a sheet steel enclosure suitable for wall mounting with a hinged, lockable 

The control panel comprises of a sheet steel enclosure suitable for wall mounting with a hinged, lockable 
front access door. It can be semi recessed, using a suitable recessing bezel. Cable entry is via 20mm 

front access door. It can be semi recessed, using a suitable recessing bezel. Cable entry is via 20mm 
‘knockouts’ located at the top and rear of the cabinet.

‘knockouts’ located at the top and rear of the cabinet.

Different key types are used for the door lock and the ‘activate controls’ key-switch. It is also possible 

Different key types are used for the door lock and the ‘activate controls’ key-switch. It is also possible 
to enable the controls via a 4 digit code entry if preferred. An eight button keypad is used to control the 

to enable the controls via a 4 digit code entry if preferred. An eight button keypad is used to control the 
system and allow access to the function options. The three main buttons, ‘RESOUND’ (red), ‘SILENCE’ 

system and allow access to the function options. The three main buttons, ‘RESOUND’ (red), ‘SILENCE’ 
(blue) and ‘RESET’ (green) being much larger and colour coded to assist the end users.

(blue) and ‘RESET’ (green) being much larger and colour coded to assist the end users.

Two or four AlarmSense 

fi

 re zone circuits are provided plus two additional conventional monitored sounder 

Two or four AlarmSense 

fi

 re zone circuits are provided plus two additional conventional monitored sounder 

circuits. Fire & Fault VFCO relays, Fire & Fault switched negative outputs, class change and an alert input 

circuits. Fire & Fault VFCO relays, Fire & Fault switched negative outputs, class change and an alert input 
are also included. 

are also included. 

The panels are supplied with a 1.5 amp internal power supply module. This module complies with the 

The panels are supplied with a 1.5 amp internal power supply module. This module complies with the 
requirements of EN54-4 : 1988 and provides temperature compensated battery management charging.

requirements of EN54-4 : 1988 and provides temperature compensated battery management charging.

Quiesecent and alarm current details for standby battery calculations

Model

Standby Current

Alarm Current

ALS-2

75mA

116mA

ALS-4

85mA

133mA

www.acornfiresecurity.com

www.acornfiresecurity.com

Содержание AlarmSense













































Отзывы:

Нет отзывов