Hachette AGORA BISMARCK THE LEGENDARY BATTLESHIP Скачать руководство пользователя

Страница: 7 / 45

Fix the right rangefinder hood

70-06

to the right-

hand side of the gun turret housing in the same way.

Holding the gun turret assembly in place, carefully
turn over the deck assembly. Fit the cog

70-04

place on the underside of the gun turret. A tab on
part

70-02

fits into a notch in part

70-04

. Fix in

place with three

1.7 x 6mm screws.

Fit the gun barrels

70-03

through the holes in the

front of the gun turret

70-01

and position the cradle

so that the two tabs fit into recesses in the gun turret
(see arrows).

70-01

70-05

70-01

70-03

70-06

70-02

70-01

70-02

70-01

70-04

48-01

53-01

70-02

Position the gun turret base plate

70-02

on the

underside of the gun turret housing

70-01

as shown.

Fix the base plate

70-02

in place with one

2 x 5mm screw.

Take the upper deck assembly

19-01

22-01

48-01

Fit the gun turret assembly into the barbette

53-01

in the upper deck section

48-01

2 x 5

1.7 x 6

AGORA

MODELS

AGORA

MODELS

Содержание AGORA BISMARCK THE LEGENDARY BATTLESHIP














































Результаты поиска

Содержание AGORA BISMARCK THE LEGENDARY BATTLESHIP

Отзывы:

Похожие инструкции для AGORA BISMARCK THE LEGENDARY BATTLESHIP

Бренды по названию

Популярные бренды

Hachette AGORA BISMARCK THE LEGENDARY BATTLESHIP, Инструкции по сборке

Результаты поиска

Содержание AGORA BISMARCK THE LEGENDARY BATTLESHIP

Отзывы:

Похожие инструкции для AGORA BISMARCK THE LEGENDARY BATTLESHIP

Бренды по названию

Популярные бренды