Hachette AGORA BISMARCK THE LEGENDARY BATTLESHIP Скачать руководство пользователя

Страница: 36 / 45

Glue the railing

in place on the port side of the

foremast base

78-01

Take the foremast

78-03

. Check the fit of the two

central tabs on the spar

near the top of the mast.

The tabs fit into the lower two of the three holes. Glue
in place.

The railing

from frame

78-06

has to be bent to fit

around the curve on the other side of the foremast
base

78-01

(see also step 8, below).

Cut the rigging spar

from frame

78-06

. Identify

the four tabs and bend them at right angles as
shown.

Glue the railing

in place on the starboard side of

the foremast base

78-01

78-01

78-03

The railing

from frame

78-06

has to be bent to fit

around the curve at the edge of the foremast base

78-01

(see also step 7, below).

AGORA

MODELS

AGORA

MODELS

Содержание AGORA BISMARCK THE LEGENDARY BATTLESHIP














































Результаты поиска

Содержание AGORA BISMARCK THE LEGENDARY BATTLESHIP

Отзывы:

Похожие инструкции для AGORA BISMARCK THE LEGENDARY BATTLESHIP

Бренды по названию

Популярные бренды

Hachette AGORA BISMARCK THE LEGENDARY BATTLESHIP, Инструкции по сборке

Результаты поиска

Содержание AGORA BISMARCK THE LEGENDARY BATTLESHIP

Отзывы:

Похожие инструкции для AGORA BISMARCK THE LEGENDARY BATTLESHIP

Бренды по названию

Популярные бренды