9
SPECIFICATIONS
(Specifications subject to change without notice.)
CONTROLLER SPECIFICATIONS
Ranges: pH: -2 to 16 pH; mV: -2000 to +2000 mV; Temperature: -5 to +105 °C
Accuracy*: pH: ±0.02 pH; mV: ±1.0% of reading, ±35 mV non-calibrated;
Temperature: ±1.5 °C before calibration with electrode, ±0.4 °C after calibration with
electrode.
Resolution: pH: 0.01 pH; mV: 0.1 mV; Temperature: 0.1 °C
Repeatability: pH: ±0.02 pH; mV: ±0.1 mV; Temperature: ±0.2 °C
Temperature Calibration: 1 or 2 point with zero and slope adjustments
Temperature Compensation: -5 to +105 °C for Nearnst equation (auto/manual);
0 to 60 °C for auto buffer recognition
Solution Temperature Correction: Corrected to 25 °C, 0.1 to -0.1 pH units/ °C slope
Operating Temperature: -10 to 60 °C
Storage Temperature: -40 to 60 °C
Humidity Range: 5 to 90% RH non-condensing
Relative mV Adjustment: The mV zero may be offset to any point in the ±2000 range
Alarms: Alarms 1 and 2: Usable in any of operating modes, (pH/mV/Temperature).
Programmable for either low or high set point alarm. Alarm relays SPDT with contacts
rated at 5A resistive load at 30 Vrms (42.4 Vpk).
Recorder Output: Isolated 4-20 mA (adjustable to 0-20 mA at 900 ohms)
Controller Output: Proportional, Integral, Derivative. Additional resistors can be used to
provide 0 to 10 V, 0 to 1 V, or 0 to 100 mV outputs.
Input/Output (optional): RS-232C and 20 mA current loop
Signal Average: 0 to 10 seconds
Reading Update: Every 0.4 seconds
Power Requirements: 115/230 Vac (±17%), 50/60 Hz, 8 watts
Controller Enclosure: NEMA 4X/IP66 (rear connections). Suitable for 1/2-inch conduit.
Wall, panel or pole mounted. For indoor use.
Controller Dimensions: 14.4 cm x 14.4 cm x 12.5 cm deep (5.67" x 5.67" x 4.9" deep).
Panel cutout size: 14 cm x 14 cm (5.5" x 5.5")
* Intermittent Electromagnetic Radiation of 3 Volts per meter or greater may cause measurement inaccuracy. For complete
accuracy details in an RF environment, see the Supplemental Compliance Information in this manual.
Содержание EC1000
