H3C S9500E Series Скачать руководство пользователя страница 327 | Manualshive

Страница: 327 / 459

background image

327

RIPng packet processing procedure

Request packet

When a RIPng router first starts or must update some entries in its routing table, generally a

multicast request packet is sent to ask for needed routes from neighbors.
The receiving RIPng router processes RTEs in the request. If there is only one RTE with the IPv6
prefix, with the prefix length both being 0 and with a metric value of 16, then the RIPng router

will respond with the entire routing table information in response messages. If there are multiple

RTEs in the request message, the RIPng router will examine each RTE, update its metric, and send

the requested routing information to the requesting router in the response packet.

Response packet

The response packet containing the local routing table information is generated as follows:

•

A response to a request

•

An update periodically

•

A trigged update caused by route change

After receiving a response, a router checks the validity of the response before adding the route to

its routing table, such as whether the source IPv6 address is the link-local address and whether the
port number is correct. The response packet that failed the check is discarded.

Protocols and standards

•

RFC 2080: RIPng for IPv6

•

RFC 2081: RIPng Protocol Applicability Statement

Configuring RIPng basic functions

This section presents the information to configure the basic RIPng features.
You must enable RIPng first before configuring other tasks, but it is not necessary for RIPng-related
interface configurations, such as assigning an IPv6 address.

Prerequisites

•

Enable IPv6 packet forwarding.

•

Configure an IP address for each interface, and ensure all nodes are reachable to one
another.

To do…

Use the command…

Remarks

Step 1

Enter system view

system-view

––

Step 2

Create a RIPng process
and enter RIPng view

ripng

[

process-id

]

Required
Not created by default

«
...
325
326
327
328
329
...
»

Содержание S9500E Series












































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S9500E Series

Бренд: Garmin Страницы: 4

Бренд: YUGE Страницы: 69

Бренд: Quectel Страницы: 232

Бренд: Quectel Страницы: 9

Бренд: Quectel Страницы: 73

Бренд: Balboa Water Group Страницы: 88

Бренд: ABB Страницы: 2

MicroTech II UV05

Бренд: AAF Страницы: 50

Бренд: DeLaval Страницы: 102

Бренд: Gemini Страницы: 9

Бренд: M-system Страницы: 18

Бренд: Comparato Страницы: 20

Бренд: DSC Страницы: 16

MultiConnect Dragonfly MTQ-MNA1-B01

Бренд: Multitech Страницы: 45

Бренд: ICP DAS USA Страницы: 7

XBee DigiMesh 2.4

Бренд: Digi Страницы: 157

Бренд: Instrutech Страницы: 42

Бренд: olympia electronics Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды