manualshive.com logo in svg

H3C S9500 Series, Руководство по управлению

Поделиться
Скачать
H3C S9500 Series Скачать руководство пользователя страница 31

Command Manual – MPLS Basics 
H3C S9500 Series Routing Switches 

Chapter 1  MPLS Basics Configuration Commands

 

1-23 

 Add route success, VRF:0 Destination: 0x8c010101 Destination mask: 0xffffffff 

Nexthop: 0x7f000001 IfIndex:0x150000 . 

*0.25275573 PE1 LSPM/8/LSPM PROCESS: 

Rcv create lsp msg from signaling protocol 0x8c010101/0xffffffff In If - 

0x300010 ! 

*0.25275812 PE1 LSPM/8/LSPM PROCESS: 

Received Signaling message. 

*0.25275812 PE1 LSPM/8/LSPM PROCESS: 

 

Received Signal CREATE message, VRF Index: 0 destination: 0x8c010101 

destination mask: 0xffffffff Nexthop: 0x7f000001 OutIfIndex: 0x150000 

InIfIndex: 0x300010  

*0.25275812 PE1 LSPM/8/LSPM PROCESS: 

 Setting MTU = LSP MTU 

*0.25275812 PE1 LSPM/8/LSPM PROCESS: 

Error: No LSP found for the route. 

*0.25275812 PE1 LSPM/8/LSPM PROCESS: 

 Added LSP in LM Successfully 

   *0.25275812 PE1 LSPM/8/LSPM PROCESS: 

Down to Agent success: evt/lsptype 1/3 

// For details, refer to the above flow. 

# Enable MPLS tunnel debugging by executing the 

debugging mpls

 

management 

tunnel

 command. 

Start two switches, connect the two switches, and configure MPLS, MPLS LDP and 

MPLS TE for them to establish a session and tunnel between them. Enable MPLS 

tunnel debugging by executing the 

debugging mpls management tunnel

 command 

on one switch while executing the 

shutdown

 command first and then the 

undo 

shutdown

 command on the other switch. 

<PE1>debugging mpls management tunnel 

<PE1> 

*0.94534296 PE1 LSPM/8/LSPM TUNNEL: 

 Begin physic check,ulIfIndex:3407872 

*0.94534296 PE1 LSPM/8/LSPM TUNNEL:                                              

 TE tunnel get mode data ok when check physic,ulTunnelIfIndex:3407872            

*0.94534296 PE1 LSPM/8/LSPM TUNNEL:                                              

 End physic check,the tunnel can up           

// The interfaces are Up. The tunnel can be Up. 

%Dec 23 10:51:12:310 2005 PE1 IFNET/5/UPDOWN:                                    

 Line protocol on the interface Tunnel0 is DOWN    

// The opposite interface is shut down, so the tunnel is down. 

*0.94564310 PE1 LSPM/8/LSPM TUNNEL:  

Содержание S9500 Series































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды