H3C S5120-SI Series Скачать руководство пользователя страница 145

Страница: 145 / 209

134

mac-address

mac-address

: Displays the MAC address-to-VLAN entry containing the specified MAC

address.

mask

mac-mask

: Displays the MAC address-to-VLAN entries with their MAC addresses in the specified

range.

static

: Displays the statically configured MAC address-to-VLAN entries.

vlan

vlan-id

: Displays the MAC address-to-VLAN entries associated with the specified VLAN.

: Filters command output by specifying a regular expression. For more information about regular

expressions, see the

Fundamentals Configuration Guide

begin

: Displays the first line that matches the specified regular expression and all lines that follow.

exclude

: Displays all lines that do not match the specified regular expression.

include

: Displays all lines that match the specified regular expression.

regular-expression

: Specifies a regular expression, which is a case sensitive string of 1 to 256

characters.

Description

Use the

display mac-vlan

command to display the specified MAC address-to-VLAN entries.

mac-address

mac-address

is specified but

mask

is not specified, only the MAC address-to-VLAN entry

containing the specified MAC address is displayed.

Examples

# Display all the MAC address-to-VLAN entries.

<Sysname> display mac-vlan all

The following MAC-VLAN address exist:

S: Static D: Dynamic

MAC ADDR MASK VLAN ID PRIO STATE

-------------------------------------------------------------------

0008-0001-0000 FFFF-FF00-0000 5 3 S

0002-0001-0000 FFFF-FFFF-FFFF 5 3 S&D

Total MAC VLAN address count:2

Table 31

Output description

Field Description

S: Static

The character

stands for the MAC address-to-VLAN entries that are

configured statically.

D: Dynamic

The character

stands for the MAC address-to-VLAN entries that are

configured dynamically.

MAC ADDR

MAC address of a MAC address-to-VLAN entry.

MASK

Mask of the MAC address of a MAC address-to-VLAN entry.

VLAN ID

VLAN ID of a MAC address-to-VLAN entry.

PRIO

802.1p priority corresponding to the MAC address of a MAC
address-to-VLAN entry.

Содержание S5120-SI Series


















































































































































































































Результаты поиска

Содержание S5120-SI Series

Отзывы:

Бренды по названию

Популярные бренды

H3C S5120-SI Series, Справочник по командам

Результаты поиска

Содержание S5120-SI Series

Отзывы:

Бренды по названию

Популярные бренды