H3C H3C S7500E-X Скачать руководство пользователя | Manualshive

Страница: 230 / 290

background image

217

Configuring LLDP

Overview

In a heterogeneous network, a standard configuration exchange platform makes sure different types
of network devices from different vendors can discover one another and exchange configuration.

The Link Layer Discovery Protocol (LLDP) is specified in IEEE 802.1AB. The protocol operates on
the data link layer to exchange device information between directly connected devices. With LLDP, a
device sends local device information as TLV (type, length, and value) triplets in LLDP Data Units
(LLDPDUs) to the directly connected devices. Local device information includes its system
capabilities, management IP address, device ID, port ID, and so on. The device stores the device
information in LLDPDUs from the LLDP neighbors in a standard MIB. For more information about
MIBs, see

Network Management and Monitoring Configuration Guide

. LLDP enables a network

management system to quickly detect and identify Layer 2 network topology changes.

Basic concepts

LLDP agent

An LLDP agent is a mapping of an entity where LLDP runs. Multiple LLDP agents can run on the
same interface.

LLDP agents are divided into the following types:

•

Nearest bridge agent.

•

Nearest customer bridge agent.

•

Nearest non-TPMR bridge agent.

A Two-port MAC Relay (TPMR) is a type of bridge that has only two externally-accessible bridge
ports. It supports a subset of the functions of a MAC bridge. A TPMR is transparent to all
frame-based media-independent protocols except for the following:

•

Protocols destined to it.

•

Protocols destined to reserved MAC addresses that the relay function of the TPMR is
configured not to forward.

LLDP exchanges packets between neighbor agents and creates and maintains neighbor information
for them.

shows the neighbor relationships for these LLDP agents. LLDP has two bridge

modes: customer bridge (CB) and service bridge (SB).

Figure 69 LLDP neighbor relationships

«
...
228
229
230
231
232
...
»

Содержание H3C S7500E-X



































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для H3C S7500E-X

Бренд: D-Link Страницы: 12

Бренд: B2 Страницы: 52

Бренд: Paradyne Страницы: 20

Compshere 3000 Series

Бренд: Paradyne Страницы: 2

Бренд: Paradyne Страницы: 2

Parallel Printer Card PIOC

Бренд: B&B Electronics Страницы: 16

kontron COMe-cEL6

Бренд: S&T Страницы: 99

Бренд: Moxa Technologies Страницы: 2

SABVISION NVR32

Бренд: SAB Страницы: 29

Бренд: Omron Страницы: 13

Бренд: Alarm Страницы: 5

Disc Publisher XR

Бренд: Primera Страницы: 2

NexXxoS GPX-N 1070-M08

Бренд: Alphacool Страницы: 4

Бренд: ANTAIRA Страницы: 6

Бренд: Z3 Technology Страницы: 83

Бренд: Agilent Technologies Страницы: 458

Dablet DVP 5000

Бренд: DarbeeVision Страницы: 10

Kontron OSM-S i.MX8M Mini

Бренд: S&T Страницы: 41

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды