H3C DSIC-9FSW Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 219

background image

26

Table 35 LED description

LED

Description

LINK

•

Off: The link is idle.

•

On: The link is being occupied for call connection.

ACT

•

Off: The link is idle.

•

On: The link is being occupied for communication.

Interface cables and the connection methods

For more information about FXS/FXO interface cables and the connection methods, see
"

ADSL/BS/FXS/FXO/AM/FCM interface

."

SIC-2FXS1FXO

Introduction

The 2-port analog subscriber circuit interface module and 1-port voice AT0 loop trunk interface
module (SIC-2FXS1FXO) serve to access and handle three channels of analog voice signals over
data communication networks. Two FXS interfaces and one FXO interface are available on a
SIC-2FXS1FXO module:

•

FXS interfaces are analog subscriber line interfaces that provide ordinary analog telephone and
fax access and also can connect AT0 loop trunks of exchanges.

•

FXO interfaces are loop trunk interfaces that provide access of common subscriber lines of
exchanges.

Interface specifications

Table 36 Interface specifications

Item Description

Connector type

RJ-11

Number of connectors

2 FXS interfaces
1 FXO interface

Interface standard

•

Supports subscriber circuit interface (FXS), compliant with ITU Q.512

•

Supports loop trunk interface (FXO), compliant with ITU Q.552

•

Over-current and over-voltage protection compliant with ITU K.20

Cable type

Telephone cable with ferrite core

Dial-up mode

Supports DTMF, compliant with GB3378, but does not support pulse dial-up.

Bandwidth

300 Hz to 3400 Hz

«
...
33
34
35
36
37
...
»

Содержание DSIC-9FSW




























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DSIC-9FSW

Бренд: 1Control Страницы: 8

Бренд: VAT Страницы: 26

Бренд: Hach Страницы: 2

Бренд: Hach Страницы: 12

Бренд: Hach Страницы: 472

Бренд: Hach Страницы: 64

Бренд: V2 ELETTRONICA Страницы: 6

Бренд: Hach Страницы: 210

Бренд: Veeder-Root Страницы: 27

Бренд: Valve Concepts Страницы: 18

Бренд: K&K Страницы: 6

Бренд: Samson Страницы: 78

Бренд: ZPA Pecky, a.s. Страницы: 36

Pulsafeeder MPC Vector

Бренд: Idex Страницы: 114

Бренд: Maximum Controls Страницы: 58

RDS17S-ELITE1-R1

Бренд: D&R ELECTRONICS Страницы: 12

iDual A E27 iD60

Бренд: jedi LIGHTING Страницы: 23

Бренд: Reliance Foundry Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды