H3C DSIC-9FSW Скачать руководство пользователя страница 139

Страница: 139 / 219

130

Table 177 Set the jumpers on the FIC-4BSE

Jumper settings & description

Default

Interface 0

•

To use a 100-ohm matched resistance for data transmission,
place the jumper over pins 1 and 2.

•

To do otherwise, place the jumper over jump pins 2 and 3.

•

See

Figure 146

The jumpers
are placed over
jump pins 2 and
3, meaning
100-ohm
matched
resistances are
not used.

•

To use a 100-ohm matched resistance for data receiving,
place the jumper over jump pins 1 and 2.

•

To do otherwise, place the jumper over jump pins 2 and 3.

•

See

Figure 146

Interface 1

•

To use a 100-ohm matched resistance for data transmission,
place the jumper over pins 1 and 2.

•

To do otherwise, place the jumper over jump pins 2 and 3.

•

See

Figure 146

•

To use a 100-ohm matched resistance for data receiving,
place the jumper over jump pins 1 and 2.

•

To do otherwise, place the jumper over jump pins 2 and 3.

•

See

Figure 146

Interface 2

•

To use a 100-ohm matched resistance for data transmission,
place the jumper over pins 1 and 2.

•

To do otherwise, place the jumper over jump pins 2 and 3.

•

See

Figure 146

•

To use a 100-ohm matched resistance for data receiving,
place the jumper over jump pins 1 and 2.

•

To do otherwise, place the jumper over jump pins 2 and 3.

•

See

Figure 146

Interface 3

•

To use a 100-ohm matched resistance for data transmission,
place the jumper over pins 1 and 2.

•

To do otherwise, place the jumper over jump pins 2 and 3.

•

See

Figure 146

•

To use a 100-ohm matched resistance for data receiving,
place the jumper over jump pins 1 and 2.

•

To do otherwise, place the jumper over jump pins 2 and 3.

•

See

Figure 146

Interface LEDs

Figure 147 FIC-4BSE panel

Содержание DSIC-9FSW




























































































































































































































Результаты поиска

Содержание DSIC-9FSW

Отзывы:

Похожие инструкции для DSIC-9FSW

Бренды по названию

Популярные бренды

H3C DSIC-9FSW, Руководство пользователя

Результаты поиска

Содержание DSIC-9FSW

Отзывы:

Похожие инструкции для DSIC-9FSW

Бренды по названию

Популярные бренды