H3C DSIC-9FSW Скачать руководство пользователя страница 110

Страница: 110 / 219

101

The FIC-16FSWP and DFIC-24FSW interface modules each also provide a PoE LED to indicate the
PoE status.

NOTE:

The two GE interfaces on the DFIC-24FSWP do not support PoE.

Interface cables and the connection methods

For more information about Ethernet interface cables and the connection methods, see "

Ethernet

interface

Ethernet interface module

•

FIC-1FE

•

FIC-2FE

•

FIC-4FE

•

FIC-1GBE

•

FIC-2GBE

•

FIC-1GEF

•

FIC-2GEF

FIC-1FE/FIC-2FE/FIC-4FE

Introduction

The 1-port, 2-port, and 4-port 10Base-T/100Base-TX fast Ethernet interface modules (FIC-1FE,
FIC-2FE, and FIC-4FE) are mainly used for the communication between router and LAN.

The modules support:

•

100 m (328.08 ft) of transmission segment over the category-5 twisted-pair cable

•

Operation at 100 Mbps and 10 Mbps, autosensing

•

Full duplex and half-duplex, with the former in common use

Interface specifications

Table 140 Interface specifications

Item FIC-1FE

FIC-2FE

FIC-4FE

Connector

RJ-45

Number of connectors

1 2 4

Cable

Straight-through Ethernet cable

Operating mode

Full duplex/half-duplex
10/100 Mbps autosensing

Содержание DSIC-9FSW




























































































































































































































Результаты поиска

Содержание DSIC-9FSW

Отзывы:

Похожие инструкции для DSIC-9FSW

Бренды по названию

Популярные бренды

H3C DSIC-9FSW, Руководство пользователя

Результаты поиска

Содержание DSIC-9FSW

Отзывы:

Похожие инструкции для DSIC-9FSW

Бренды по названию

Популярные бренды