H3C DSIC-9FSW Скачать руководство пользователя страница 160

Страница: 160 / 219

151

Interface Features

Table 205 Interface specifications

Item Description

Protocol supported

IPSec

Hardware algorithm

key algorithm (DES, 3DES, AES)
Authentication algorithm (HMAC-MD5-96, HMAC-SHA-1-96)

Panel and LEDs

Figure 171 FIC-HNDE panel

Table 206 LED description

LED Description

STATUS

•

Steady green: Power is being supplied to the FIC-HNDE normally.

•

Off: The module is not powered, the power supply of the module has failed or a
serious hardware fault occurs.

ACTIVE

•

Off after two-second flashing (yellow): The module has been initialized.

•

Flashing: The module operates normally and data is being transmitted or received.

•

Off: The module is operating normally but not sending or receiving data.

Troubleshooting

You can learn how well the encryption module is operating by reading the LEDs on it.

For the correct LED behaviors, see

Table 207

Table 207 Troubleshooting by reading the LED behaviors

Incorrect LED behaviors

Reason

Action to take

STATUS LED remains off at
router startup.

The module or some
hardware parts on the
module are not supplied
with power properly.

Check that the power supply of the
router is correctly connected.

Check that the power is being supplied.

Contact your sales agent for help: the
power supply of the module may have
been damaged or anomalies have
occurred to the CPLD.

ACTIVE LED remains off at
device startup.

The encryption processor
failed to initialize the
configurations possibly
due to a system bus
problem.

Check that the module is securely
connected to the host.

Contact your sales agent for help: the
host or the module may be problematic.

Содержание DSIC-9FSW




























































































































































































































Результаты поиска

Содержание DSIC-9FSW

Отзывы:

Похожие инструкции для DSIC-9FSW

Бренды по названию

Популярные бренды

H3C DSIC-9FSW, Руководство пользователя

Результаты поиска

Содержание DSIC-9FSW

Отзывы:

Похожие инструкции для DSIC-9FSW

Бренды по названию

Популярные бренды