H2X THERAPOOL SE Скачать руководство пользователя страница 73

Страница: 73 / 108

DO NOT DIVE.

Swim spa Controls

Sensor-Related Messages

Miscellaneous Messages

127

DO NOT DIVE.

SENSORS ARE OUT OF SYNC – M015**

The temperature sensors MAY be out of sync by 3°F (1°C). Call for service if this message does not
disappear within a few minutes.

SENSORS ARE OUT OF SYNC -- CALL FOR SERVICE* – M026**

The temperature sensors ARE out of sync. The fault above has been established for at least 1 hour.
Call for service.

COMMUNICATIONS ERROR

The control panel is not receiving communication from the System. Call for service.

TEST SOFTWARE INSTALLED

The Control System is operating with test software. Call for service.

SENSOR A FAULT, SENOR B FAULT –
SENSOR A: M031**, SENSOR B: M032**

A temperature sensor or sensor circuit has
failed. Call for service.

* Some messages can be reset from the panel. Messages that can be reset will appear with a Clear

Icon at the bottom of the Message Screen. Press the Clear Icon text to reset the message.

**M0XX is a Message Code. Codes like this will be seen in the Fault Log

Содержание THERAPOOL SE













































































































Результаты поиска

Содержание THERAPOOL SE

Отзывы:

Похожие инструкции для THERAPOOL SE

Бренды по названию

Популярные бренды

H2X THERAPOOL SE, Руководство пользователя

Результаты поиска

Содержание THERAPOOL SE

Отзывы:

Похожие инструкции для THERAPOOL SE

Бренды по названию

Популярные бренды