GW Instek PCS-1000 Скачать руководство пользователя страница 63

Страница: 63 / 93

COMMUNICATION INTERFACE

Example

CONF:CURR 20
Sets the current mode to DC and the range to 30A

Example

CONF:CURR
Sets the current mode to DC. The range is not
changed.

CONFigure:CURRent:AC

Set

Description

This command will set current mode to AC and set
the range. If the range is not specified, then it will
not change.

Syntax

CONFigure:CURRent:AC [<Range> | AUTO]

Parameter

<Range>

Current range <NRf>: 0.00000001~305
Current range. The unit will
automatically be set to the closest range.

AUTO

Autorange; Only applicable for the ≤3A
ranges.
Autorange is not supported for the 30A
and 300A ranges.

Example

CONF:CURR:AC 100
Sets the current mode to AC and the range to 300A.

Example

CONF:CURR:AC
Sets the current mode to AC. The range is not
changed.

CONFigure:VOLTage

Query

Description

The CONFigure:VOLTage query will return the
voltage mode and the voltage range unit.

Query Syntax

CONFigure:VOLTage?

Return Parameter <string>

Returns the voltage mode and range unit.

Содержание PCS-1000






























































































Результаты поиска

Содержание PCS-1000

Отзывы:

Похожие инструкции для PCS-1000

Бренды по названию

Популярные бренды

GW Instek PCS-1000, Руководство пользователя

Результаты поиска

Содержание PCS-1000

Отзывы:

Похожие инструкции для PCS-1000

Бренды по названию

Популярные бренды