Gude Expert Net Control 2304 страница 22 Скачать руководство пользователя

Страница: 22 / 87

Expert Net Control 2304

Operating

"GBL_Conf.exe" can disable the password and the IP ACL, perform a firmware update,
and restore the factory settings.

For devices with relays, entering or exiting the bootloader mode does not change

the state of the relays as long as the operating voltage is maintained.

Abandonment of the Bootloader Mode

1) via push button:

Hold both buttons for 3 seconds (only if the device has 2 buttons)

2) or

Remove and connect the power supply without operating a button

3) by Software:

Start the "GBL_Conf.exe" application

Do a network search with the "Search" menu action

In menu

Program Device

activate the item "Enter Firmware"

For devices with relays, entering or exiting the bootloader mode does not change

the state of the relays as long as the operating voltage is maintained.

Factory Reset

If the device is in bootloader mode, it can always be put back to its factory default. All
TCP/IP settings are reset in this operation.

If a unit is set to factory defaults, an uploaded certificate or updated firmware will

be preserved.

1) via push button:

Activate the Bootloader Mode of the device

Hold down the button (or the "Select" button for devices with 2 buttons) for 6
seconds. If the push button is recessed, use a pin or paper clip

The status LED will blink in a fast rhythm, please wait until the LED blinks slowly
(about 5 seconds)

2) by Software:

Activate the Bootloader Mode of the device

"Start the GBL_Conf.exe" program

In menu "Program Device

activate the item

"Reset to Fab Settings"

The status LED will blink in a fast rhythm, please wait until the LED blinks slowly
(about 5 seconds)

Содержание Expert Net Control 2304
























































































Результаты поиска

Содержание Expert Net Control 2304

Отзывы:

Похожие инструкции для Expert Net Control 2304

Бренды по названию

Популярные бренды

Gude Expert Net Control 2304, Руководство пользователя

Результаты поиска

Содержание Expert Net Control 2304

Отзывы:

Похожие инструкции для Expert Net Control 2304

Бренды по названию

Популярные бренды