Gude Expert Net Control 2304 страница 27 Скачать руководство пользователя

Страница: 27 / 87

Expert Net Control 2304

Configuration

3.2

Input Ports

Choose Input port to configure: This field is used to select the input port to be con-
figured.

Name: You can assign a name up to 15 characters for each of the Input Ports. Using
the name, an identification of the the device connected to the port can be facilitated.

Inverted Input: Inverts the assignment of the input signal to a logical HI / LOW state.

Input HI Text Message: Text display in the control panel and messages when a HI sig-
nal is present at the input port.

Input LOW Text Message: Text display in the control panel and messages when a
LOW signal is present at the input port.

Enable input events: Enables Input Port monitoring.

Message Channels: Enables the generation of messages on different channels.

Console push-messages

This option allows the output of sensor values on the con-

sole at a configured time interval, or when a certain threshold has been reached.

On input is HI: Switching action when Input Port changes from LOW to HI.

On input is LOW: Switching action when Input Port changes from HI to LOW.

Console push-messages

This option allows the output of sensor values on the con-

sole at a configured time interval, or when a certain threshold has been reached.

Содержание Expert Net Control 2304
























































































Результаты поиска

Содержание Expert Net Control 2304

Отзывы:

Похожие инструкции для Expert Net Control 2304

Бренды по названию

Популярные бренды

Gude Expert Net Control 2304, Руководство пользователя

Результаты поиска

Содержание Expert Net Control 2304

Отзывы:

Похожие инструкции для Expert Net Control 2304

Бренды по названию

Популярные бренды