background image

Giraud Tool Company, Inc.

 

 

GIRAUD POWERED CASE TRIMMER 

Page 3 of 10 

holder.  Rotating the case holder from one mark to another (45º) with move the 
case holder approximately 0.009” 
 
With some of your older or scrap RESIZED cartridge cases, trim a few cases to 
check out the operation of your new trimmer.  Insert a case into the shell holder 
and press the case into the trimmer blade while the machine is running.  If the 
motor is bogged down or stops, the speed at which you inserted the case is too 
fast.  Gently but firmly will do, you don't have to jam it in there.  As you press into 
case holder, you will feel the vibration as the carbide blade removes material 
from the case mouth, when it stops, simply twist the still inserted case with your 
finger tips to even out the freshly cut surfaces.  
 
Check the case mouth on your first case.  You should see the case mouth bright 
and shiny where the brass has been trimmed.  If the case mouth is not uniformly 
trimmed around the entire diameter, it is because the runout between the cutting 
blade and case holder are just slightly out of alignment or the case neck is not 
concentric with the case body.  It only takes a thousandth or two to cause that.  
But you can easily correct or overcome this by twisting the case a half turn or 
more while the case is touching the rotating blade.  As the case rotates and 
blade rotates, the entire case mouth makes contact with the entire travel of the 
blade.  It sounds more complicated than it really is.  Just give them a twist and 
they come out pretty uniform. 

 
Next, check your overall length of the 
trimmed case with a caliper.  I will set 
the length fairly close, but it will really 
depend on how you size your brass.  
Since the case trimmer locates each 
case by the case shoulder, if your 
headspace dimensions on the resized 
brass are not consistent, then the 
case can't be trimmed to a uniform 
dimension.  I suggest the use of some 
type of headspace measuring device 
to monitor your resizing operation.  
Several different brands of tools are 
available from Stoney Point, Midway, 
Neal Jones, Sinclair, and RCBS, just 
to name a few.  The simplest device 

mounts to the jaw of your dial caliper and lets you measure the consistency of 
each case quickly and easily. 

 
Using the Trimmer 
 

Trim and measure three cases.  If your dimensions are /- 0.002" on the 
overall length, you are in the ballpark.  With a little use and consistent technique, 
your cases should come out within 0.001" of each other, every time.  If the overall 
length you measured is the length you want the finished cases to be, you are 
ready to trim some brass.  If the length is too long or too short, loosen the jam nut 

 

 

 

Figure 2 - 

A properly trimmed case has a chamfer that is 

even and smooth around the entire case mouth, both 
inside and outside.  

Содержание POWERED CASE TRIMMER











Отзывы: