GSi PNEG-902 Скачать руководство пользователя страница 4

4

   

PNEG-902 

Multi - Module Dryer Stacking

1. Safety

Safety Guidelines

This manual contains information that is important for you, the owner/operator, to know and understand. 
This information relates to protecting

 personal safety 

and 

preventing equipment

 

problems

. It is the 

responsibility of the owner/operator to inform anyone operating or working in the area of this equipment 
of these safety guidelines. To help you recognize this information, we use the symbols that are defined 
below. Please read the manual and pay attention to these sections. Failure to read this manual and its 
safety instructions is a misuse of the equipment and may lead to serious injury or death.

This is the safety alert symbol. It is used to alert you to 
potential personal injury hazards. Obey all safety 
messages that follow this symbol to avoid possible 
injury or death.

WARNING

 indicates a potentially hazardous situation 

which, if not avoided, could result in death or serious injury.

CAUTION

 indicates a potentially hazardous situation which, 

if not avoided, may result in minor or moderate injury.

CAUTION 

used without the safety alert symbol indicates a 

potentially hazardous situation which, if not avoided, may 
result in property damage.

NOTE

 indicates information about the equipment that you 

should pay special attention to.

DANGER

 indicates an imminently hazardous situation 

which, if not avoided, will result in death or serious injury.

Содержание PNEG-902





















Отзывы: