manualshive.com logo in svg

GSi PNEG-902, Руководство по установке

Поделиться
Скачать
GSi PNEG-902 Скачать руководство пользователя страница 17

PNEG-902 

Multi - Module Dryer Stacking

17

5. Ladder Cage Installation

1. To install the safety cage for the rear ladder of the bottom module, connect two (2) large bell hoop 

halves (LS-4352) together and connect two (2) small bell hoop halves (LS-4351) together. Attach  
a safety cage bracket (LS-4349) to each end of those assemblies. Use 5/16"-18 x 3/4" bin bolts 
(S-275) and 5/16"-18 nuts (S-3611) 

(See Figure 5A

, 

Figure 5B

 and 

Figure 5C.)

2. Use five (5) 44" safety cage vertical supports (LS-4353) and connect the small and large bell hoops 

assembled in the 

Step 1

 using 5/16"-18 x 3/4" bin bolts (S-275) and 5/16"-18 nuts (S-3611). 

NOTE: Leave one side of this assembly open so the rear access door on the dryer will 
not be obstructed

.

3. Now locate the safety cage bolt holes on the ladder 

(See Figure 5A.)

 Use 5/16"-18 x 3/4" bin bolts 

(S-275) and 5/16"-18 nuts (S-3611) to install safety cage onto the ladder.

Figure 5A 

Figure 5B 

Figure 5C 

Safety cage bolt holes

LS-4351
(Small bell hoop halves)

LS-4349

(Safety cage brackets)

Содержание PNEG-902





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды