22
DRYER START UP
STARTING THE DRYER
This start up procedure is for a cold start on wet grain for continuous flow
operation.
1.
Set the MAXON or FAST ACTION HAND VALVE on the incoming fuel
line to the ON position.
2.
Make sure the MOISTURE CONTROL switch is in the OFF position.
3.
Turn the FAN switch to the ON position.
4.
Adjust the AIR PRESSURE SWITCH if necessary.
5.
Turn the HEATER switch to the ON position. The heater will purge for
about 10 seconds then ignite. If flame is detected the dryer will run, if
not a "loss of flame" error will occur. If this happens check gas supply,
and all valves in the fuel line to make sure they are ON.
ADJUSTING THE TEMPERATURE
1.
Press the PROGRAM(TEMPERATURES) button until the "carrot" is
above the timer you want to modify.
2.
Use the up and down arrow keys to change from the present tempera-
ture to the desired setting. The new temperature is automatically ac-
cepted.
3.
Keep pressing the PROGRAM(TEMPERATURES) button until the car-
rot disappears or press the MODE SELECT button once to exit.
4.
On LP gas models adjust the PRESSURE REGULATOR (high fire) on
the burner fuel line, so that burner will reach the thermostat setting and
switch to (low fire) (pressures may be required up to 25 lbs.). Natural
gas does not have a regulator, but uses a LARGE BALL VALVE close
to
the
vertical supply line for adjustment (pressures may be re-
quired up to
18 lbs.).
On LP gas models adjust the small RED HANDLED BALL VALVE
(low fire) so that the burner maintains flame then switches back to (high
fire). Natural gas has a BALL VALVE close to the burner control box,
for low fire adjustment.
5.
Adjust the burner pressure so that the burner CYCLES 4 times per
minute (approx. 10 sec. on HIGH--approx. 5 sec. on LOW). When on
HIGH FIRE increasing the pressure with the pressure regulator
DE-
CREASES
the time spent on high fire. When on LOW FIRE increasing
the low fire pressure with the RED BALL VALVE
INCREASES
the time
spent on low fire.
6.
On LP gas models adjust the VAPORIZER so the fuel pipes going to
the burner from the regulator are warm to the touch (not hot and cold).
How much gas pressure do I
use?
See step number four in
the
Adjusting The Temperature
section.
How often should my burner
cycle?
See step number five in
the
Adjusting The Temperature
section.
Содержание COMPETITOR 2000 Series
