Grundfos SPKE, Инструкция по установке и эксплуатации

Страница: 3 / 28

3
CONTENTS
Page
1. Symbols used in this document 3
2. General 4
3. Installation 4
3.1 Motor cooling 4
3.2 Outdoor installation 4
3.3 Electrical connection – single-phase pumps 4
3.3.1 Mains switch 4
3.3.2 Protection against electric shock – indirect contact 4
3.3.3 Additional protection 5
3.3.4 Motor protection 5
3.3.5 Overvoltage protection 5
3.3.6 Supply voltage 5
3.3.7 Start/stop of pump 5
3.4 Other connections 5
3.5 Electrical connection – three-phase pumps,
0.75-7.5 kW
6
3.5.1 Mains switch 6
3.5.2 Protection against electric shock – indirect contact 6
3.5.3 Additional protection 6
3.5.4 Motor protection 6
3.5.5 Overvoltage protection 7
3.5.6 Supply voltage 7
3.5.7 Start/stop of pump 7
3.6 Other connections 7
3.7 Electrical connection – three-phase pumps, 11-22 kW 8
3.7.1 Mains switch 8
3.7.2 Protection against electric shock - indirect contact 8
3.7.3 Additional protection 8
3.7.4 Motor protection 8
3.7.5 Protection against mains voltage transients 8
3.7.6 Supply voltage 8
3.7.7 Start/stop of pump 8
3.8 Other connections 9
3.9 Signal cables 9
3.10 Bus connection cable 9
3.10.1 New installations 9
3.10.2 Replacing an existing pump 9
4. Setting the pump 10
4.1 Pumps without factory-fitted sensor 10
4.2 Pumps with pressure sensor 10
4.3 Factory setting 10
5. Setting by means of control panel 10
5.1 Setpoint setting 11
5.1.1 Pump in controlled-operation mode (pressure control) 11
5.1.2 Pump in uncontrolled-operation mode
11
5.2 Setting to max. curve duty 11
5.3 Setting to min. curve duty 11
5.4 Start/stop of pump 11
6. Setting by means of R100 11
6.1 Menu OPERATION 13
6.1.1 Setpoint setting 13
6.1.2 Setting of operating mode 13
6.1.3 Fault indications 13
6.1.4 Alarm log 13
6.2 Menu STATUS 13
6.2.1 Display of actual setpoint 14
6.2.2 Display of operating mode 14
6.2.3 Display of actual value 14
6.2.4 Display of actual speed 14
6.2.5 Display of input power and power consumption 14
6.2.6 Display of operating hours 14
6.3 Menu INSTALLATION 14
6.3.1 Selection of control mode 14
6.3.2 Setting of controller 14
6.3.3 Selection of external setpoint signal 15
6.3.4 Selection of fault, operating or ready signal relay 15
6.3.5 Blocking of the buttons on the pump 15
6.3.6 Allocation of pump number 15
6.3.7 Selection of function for digital input 16
6.3.8 Setting of stop function 16
6.3.9 Setting of sensor 17
6.3.10 Duty/standby 17
6.3.11 Setting of min. and max. curves 17
7. External forced-control signals 17
7.1 Start/stop input 17
7.2 Digital input 18
8. External setpoint signal 18
9. Bus signal 19
10. Priority of settings 19
11. Indicator lights and signal relay 20
12. Megging 21
13. Technical data – single-phase pumps 21
13.1 Supply voltage 21
13.2 Leakage current 21
13.3 Inputs/output 21
14. Technical data – three-phase pumps, 0.75-7.5 kW 21
14.1 Supply voltage 21
14.2 Leakage current 21
14.3 Inputs/output 22
15. Technical data – three-phase pumps, 11-22 kW 22
15.1 Supply voltage 22
15.2 Leakage current 22
15.3 Inputs/output 22
15.4 Other technical data 23
16. Re-lubrication of motor motor bearings
(MMGE motors)
23
17. Disposal 23
1. Symbols used in this document
Warning
Prior to installation, read these installation and
operating instructions. Installation and operation
must comply with local regulations and accepted
codes of good practice.
Warning
If these safety instructions are not observed, it
may result in personal injury!
Caution
If these safety instructions are not observed, it
may result in malfunction or damage to the
equipment!
Note
Notes or instructions that make the job easier
and ensure safe operation.
Grundfos.bk Page 3 Tuesday, April 17, 2007 8:54 AM