background image

En
gl

is

h (
G

B)

8

5. Identification

5.1 Nameplates

The pump and motor nameplates are positioned on 
the motor fan cover or terminal box.
The data and information on the pump nameplate 
are described in the table below. See the nameplate 
in fig. 6 on page 15.

The data and information on the motor nameplate 
are described in the table below. See the nameplate 
in fig. 7 on page 15.

6. Mechanical installation

Before installing the pump, check that the pump type 
and parts are as ordered.

6.1 Installation of pump

The pump must be installed with the motor shaft 
vertical. It must be mounted on a plane surface and 
secured by foundation bolts.
The pump should be installed so that the suction 
pipe is as short and the suction lift as small as 
possible.
The pump should be sited in a well ventilated but 
frost-free position. See section 

10.1 Frost protection

.

The pump may be sited outdoors, but it should be 
protected from the elements by means of a suitable 
cover.
The pump should be installed with easy access for 
inspection, maintenance and service.

6.2 Pipework

It is advisable to fit isolating valves on either side of 
the pump. It is thus not necessary to drain the 
system if the pump needs service. If the pump is 
installed above the liquid level, a non-return valve 
must be fitted in the suction pipe below the liquid 
level.
The pump must not be stressed by the pipework.
The pipework must be correctly sized taking due 
account of the pump inlet pressure.
If the pump is installed at the lowest point of the 
system, impurities and sludge may accumulate in the 
pump.
Install the pipes so that air locks are avoided, 
especially on the suction side of the pump. 
See fig. 1.

Fig. 1

Pipework

Pos.

Description

1

Pump type

2

Pump model

3

Maximum ambient temperature 
[°C] / [°F]

4

Temperature class

5

Minimum efficiency index

6

Maximum system pressure 
[bar] / [psi] / [MPa]

7

Maximum liquid temperature
[°C] / [°F]

8

Hydraulic pump efficiency at best 
efficiency point

9

Insulation class

10

Motor protection

11

Rated flow [m

3

/h] / [GPM]

12

Head at rated flow [m] / [psi]

13

Maximum head [m] / [psi]

Pos.

Description

1

Motor designation

2

Number of poles

3

Number of phases and voltage [V]

4

Rated current [A]

5

Power output [kW]

6

Power output [HP]

7

Three-phase pumps only

Motor efficiency [%]

8

Single-phase pumps only

Capacitor size [

μ

F] and voltage [V]

9

CE  mark

10

TR mark

11

IE2 mark

12

Company name and address

13

Country of manufacture

TM

01 671

0 329

9

Pos. Description

Function

1

Expansion joint

Reduces noise and 
absorbs vibrations and 
expansion.

2

Isolating valve

Enables easy service of 
the pump.

3

Pipe support

Supports pipe and 
absorbs distortion and 
strain.

1

2

3

Содержание CMV























Отзывы: