Grizzly T10096 Скачать руководство пользователя страница 8

Страница: 8 / 12

-8-

T10096 Taper Attachment

Always disconnect power

to the lathe before per-

forming maintenance.

Failure to do this may

result in serious person-

al injury.

Using an oil can with the same oil you used on
your lathe ball oilers, apply liberal amounts of oil
to the three ball oilers, the pivot pin, and the dove-
tail surface shown in

Figure

Lubrication

Vacuum excess metal chips and wipe off the
remaining metal, coolant, and oils with a dry
cloth.

If any coolant sludge has built up, use mineral
spirits to remove, and then relubricate with the
same oil you use on your lathe or use G96

Gun

Treatment, SLIPIT

, or Boeshield

T-9 to prevent

surface rust.

Cleaning

Using an oil can with the same oil you use on your
lathe ball oilers, apply oil on the knob threads and
the dovetail ways shown in

Figure

Figure 24. Lubrication locations.

Figure 25. Lubrication locations.

Содержание T10096













Результаты поиска

Содержание T10096

Отзывы:

Похожие инструкции для T10096

Бренды по названию

Популярные бренды

Grizzly T10096, Инструкция по эксплуатации

Результаты поиска

Содержание T10096

Отзывы:

Похожие инструкции для T10096

Бренды по названию

Популярные бренды