Grizzly G0795Z Скачать руководство пользователя страница 20

Страница: 20 / 64

-18-

Model G0795Z (Mfd. Since 06/17)

11. Without resetting E-Stop button, press

Forward button. Machine should not start.

—If machine does start with E-Stop button

pushed  in,  immediately  disconnect  power
to  machine.  E-Stop  safety  feature  is  not
working correctly. This safety feature must
work properly before proceeding with regu-
lar  operations.  Refer  to

Troubleshooting

Page 38 for help.

12. Twist E-Stop button clockwise to reset it.

13. Loosen downfeed selector knob slightly, to

engage coarse downfeed lever.

14. Rotate mode switch to Tap.

15. Press Forward button. Spindle should rotate

clockwise.

Note: Spindle will not engage if Reverse but-

ton is pressed while in Tap mode.

16. Use coarse downfeed lever to move spindle

down. Spindle should rotate clockwise.

17. Continue to move spindle down until it

reaches bottom of depth stop. Spindle
should momentarily stop, then rotate
counterclockwise.

18. Use coarse downfeed lever to move spindle

all the way up.

Congratulations! The

Test Run is complete.

Continue to the next subsection,

Spindle Bearing

Break-In.

8. Press Off button and wait for spindle to com-

pletely stop.

9. Press Reverse button. Spindle should rotate

counterclockwise (as viewed from top).

10. Press E-Stop button and wait for spindle to

completely stop.

4. Set Drill/Tap switch to Drill (see Figure 13).

5. Turn high/low range knob to L and adjust vari-

able-speed spindle dial until spindle reaches
a speed of about 220 RPM (see

Figure 13).

Note: When switching between gears, it may
be necessary to rotate spindle by hand so
gears will align and engage.

6. Twist E-stop button clockwise until it pops out

(see

Figure 13)—this resets the button and

enables power to control panel and motor.

7. Press Forward button (see Figure 13).

Spindle should rotate clockwise (as viewed
from top) and machine should run smoothly
with little to no vibration or rubbing noises.

Figure 13. Location of control panel and spindle

speed controls.

Forward

Button

E-Stop

Button

Reverse

Button

Drill/

Tap

Switch

Range Knob

Off

Button

Variable-Speed

Spindle Dial

Содержание G0795Z

































































Результаты поиска

Содержание G0795Z

Отзывы:

Бренды по названию

Популярные бренды

Grizzly G0795Z, Руководство пользователя

Результаты поиска

Содержание G0795Z

Отзывы:

Бренды по названию

Популярные бренды