Grizzly G0793 Скачать руководство пользователя страница 24

Страница: 24 / 60

-22-

Model G0793 (Mfd. Since 02/15)

Installing/Removing

Tooling

This machine has an MT#4 spindle for install-
ing tooling. It is also equipped with an automatic
drift for easy removal of tooling (see

Figure 16).

Additionally, a drift key is included to manually
remove the tooling from the spindle, if needed.

1. DISCONNECT MACHINE FROM POWER!

2. Lower spindle with coarse downfeed handle

until you can press in automatic drift knob
(see

Figure 16).

Leaving the automatic drift knob pressed in

can result in the arbor coming free the next

time it is inserted into the spindle sleeve.

An improperly installed arbor can become

a projectile and result in serious injury to

operator or others nearby. Always verify

arbor is correctly installed before beginning

drilling operations.

Figure 16. Location of automatic drift knob.

Automatic
Drift Knob

1. DISCONNECT MACHINE FROM POWER!

2. Clean tooling and spindle tapers to ensure

proper seating.

3. Insert MT#4 tooling into spindle, and maneu-

ver tang (see

Figure 15) until it engages with

slot at end of spindle.

4. Use rubber or wooden mallet to seat tooling

into spindle by firmly tapping from bottom.

Note:

If installing a drill chuck, make sure to

retract jaws to prevent damage to chuck.

Removing Tooling with Automatic

Drift

The Model G0793 includes the following spindle
tools (see

Figure 15):

A. B16 Drill Chuck w/MT#4–R-8 Arbor. Refer

Arbor/Chuck Assembly on Page 16.

B. MT#4–MT#3 Spindle Sleeve. Used for MT#3

tools and will accommodate tools with a tang.
It also has a drift key slot for tool removal.

C. MT#4–MT#2 Spindle Sleeve. Used for MT#2

tools and will accommodate tools with a tang.
It also has a drift key slot for tool removal.

D. Drift Key: Use for tool removal.

Cutting tools are sharp and

can easily cause laceration

injuries. Always protect

your hands with leather

gloves or shop rags when

handling cutting tools.

Installing Tapered Tooling

Figure 15. Drill chuck, arbor, spindle sleeves,

and drift key included with Model G0793.

Drift Key Slot

Tang

Содержание G0793





























































Результаты поиска

Содержание G0793

Отзывы:

Похожие инструкции для G0793

Бренды по названию

Популярные бренды

Grizzly G0793, Руководство пользователя

Результаты поиска

Содержание G0793

Отзывы:

Похожие инструкции для G0793

Бренды по названию

Популярные бренды