manualshive.com logo in svg

Grizzly G0718, Руководство пользователя

Устройство Grizzly G0718 - инструмент высокого качества для обработки древесины. Владельцам необходимо иметь в распоряжении Owner's Manual для правильной эксплуатации. Скачайте бесплатно руководство по эксплуатации с manualshive.com, чтобы использовать устройство безопасно и эффективно.

Поделиться
Скачать
background image

-4-

Model G0718 (Mfd. Since 12/10)

Machine Data Sheet

model G0718

HinGe borinG macHine

© Grizzly Industrial, Inc. • Customer Service: (800) 523-4777 • Website: www.grizzly.com

macHine daTa 

SHeeT

Product Dimensions:

Weight  ........................................................................................................................................................................... 154 lbs.
Width (side-to-side) x Depth (front-to-back) x Height ..................................................................................29 x 25 x 36-5/8 in.
Foot Print (Length x Width) ........................................................................................................................... 15-1/2 x 22-1/2 in.

Shipping Dimensions:

Type ........................................................................................................................................... Cardboard Top & Wood Pallet
Content .......................................................................................................................................................................... Machine
Weight ............................................................................................................................................................................ 198 lbs.
Length/Width/Height ...........................................................................................................................................32 x 29 x 35 in.

Electrical:

Power Requirement ...............................................................................................................110V/220V, Single-Phase, 60 Hz
Pre-Wired Voltage .............................................................................................................................................................. 110V
Full-Load Current Rating .....................................................................................................................10A at 110V, 5A at 220V
Minimum Circuit Size ........................................................................................................................15A at 110V, 15A at 220V
Switch ...........................................................................................ON/OFF Switch w/Emergency Stop Paddle & Anti-Start Pin
Switch Voltage ..........................................................................................................................................................110V/220V
Cord Length ..........................................................................................................................................................................9 ft.
Cord Gauge .................................................................................................................................................................. 14 AWG
Plug Included ........................................................................................................................................................................Yes
Included Plug Type ................................................................................................................................... NEMA 5-15 for 110V
Recommended Plug/Outlet Type .............................................................................................................. NEMA 6-15 for 220V

Motors:

Main

Type ......................................................................................................................................................................... TEFC
Horsepower ...............................................................................................................................................................1 HP
Voltage ............................................................................................................................................................110V/220V
Prewired ................................................................................................................................................................... 110V
Phase .......................................................................................................................................................... Single-Phase
Amps ....................................................................................................................................................................... 10/5A
Speed ...............................................................................................................................................................3440 RPM
Cycle ........................................................................................................................................................................ 60 Hz
Number Of Speeds ..........................................................................................................................................................1
Power Transfer ...............................................................................................................................................Direct Drive
Bearings ..................................................................................................................... Shielded and Permanently Sealed

Main Specifications:

Operation Information

Maximum Depth of Stroke ..........................................................................................................................................4 in.
Maximum Boring Depth from Edge ............................................................................................................................4 in.

Model G0718

Page 1 of 2

Содержание G0718





















































Отзывы:

Нет отзывов

Похожие инструкции для G0718

GE ImageQuant LAS 4000 Original Instructions Manual preview
ImageQuant LAS 4000
Бренд: GE Страницы: 86
GE AKTApure Operating Instructions Manual preview
AKTApure
Бренд: GE Страницы: 160
GE AKTA avant Getting Started preview
AKTA avant
Бренд: GE Страницы: 134
Raymarine P70 User Reference preview
P70
Бренд: Raymarine Страницы: 70
3M Littmann 3200 User Manual preview
Littmann 3200
Бренд: 3M Страницы: 48
3M Littmann 3100 Instructions For Use Manual preview
Littmann 3100
Бренд: 3M Страницы: 19
3M Speedglas G5-01 User Instructions preview
Speedglas G5-01
Бренд: 3M Страницы: 62
Thomas & Betts Quickfit Nexus Exit Installation Manual preview
Quickfit Nexus Exit
Бренд: Thomas & Betts Страницы: 2
Panlux MODENA Instructions preview
MODENA
Бренд: Panlux Страницы: 2
Jackco 852 User Manual preview
852
Бренд: Jackco Страницы: 6
Xo FLEX Installation Instructions Manual preview
FLEX
Бренд: Xo Страницы: 59
Falcon HT2 Installation And Servicing Instructions preview
HT2
Бренд: Falcon Страницы: 8
EASY COOPS Chicken Coop Plan 3x5 Assembly Instructions Manual preview
Chicken Coop Plan 3x5
Бренд: EASY COOPS Страницы: 21
EASY COOPS Chicken Coop Plan 4x6 Assembly Instructions Manual preview
Chicken Coop Plan 4x6
Бренд: EASY COOPS Страницы: 18
EASY COOPS Chicken Coop Plan 8x10 Assembly Instructions Manual preview
Chicken Coop Plan 8x10
Бренд: EASY COOPS Страницы: 18
Hoist Fitness HPA-2 Owner'S Manual preview
HPA-2
Бренд: Hoist Fitness Страницы: 17
Peak Pilates Wunda Assembly Manual preview
Wunda
Бренд: Peak Pilates Страницы: 4
Woods RB750-4 Operator'S Manual preview
RB750-4
Бренд: Woods Страницы: 54

Бренды по названию

Популярные бренды

Загрузить еще бренды