Grizzly G0656 Скачать руководство пользователя страница 39

G0656 8" Jointer with Built-In Mobile Base

-35-

2.

  Remove the cutterhead guard from the table 

and  lower  the  infeed  and  outfeed  tables  as 
far as they go. This will give you unrestricted 
access to the cutterhead.

3.

  Remove the rear access panel to expose the 

cutterhead pulley.

4.

  Rotate the cutterhead pulley to give you good 

access to one of the cutterhead knives.

5.

  Loosen  the  cutterhead  gib  bolts,  starting  in 

the  middle,  and  alternating  back  and  forth 
until all of the gib bolts are loose, but not fall-
ing out.

—If  this  is  the  first  time  you  are  setting  the 

knives, or if you are replacing them, remove 
a gib and knife from the cutterhead. Clean 
the  gib  and  clean  inside  the  cutterhead 
slot  to  remove  all  pitch  or  sawdust.  Coat 
the  knife  and  gib  with  a  metal  protectant 
(

Page 28

)

6.

  Position  the  knife  gauge  over  the  knife  as 

shown in 

Figure 51

 and loosen the gib bolts 

until the knife is completely loose.

7.

  Using  a  2.5mm  hex  wrench,  find  the  jack 

screws  through  the  access  holes  in  the 
cutterhead  (

Figure  53

)  and  rotate  the  jack 

screws to raise or lower the knife. When the 
knife  is  set  correctly,  it  will  barely  touch  the 
middle pad of the knife setting jig. Snug the 
gib bolts tight enough to just hold the knife in 
place. Repeat 

Steps 5-7

 with the rest of the 

knives.

Figure 53.

 Jack screw access hole.

8.

  Rotate  the  cutterhead  to  the  first  knife  you 

started with. Slightly tighten all the gib bolts, 
starting  at  the  middle  and  working  your 
way to the ends by alternating left and right 
(

Figure  54

).  Repeat  this  step  on  the  rest  of 

the knives.

9.

  Repeat 

Step  8

,  but  final  tighten  each  gib 

bolt.

10.

  Adjust  the  outfeed  table  to  match  the  new 

knife heights (refer to 

Setting Outfeed Table 

Height, Page 17

).

11.

  Replace  the  cutterhead  guard  and  the  rear 

access panel.

1

2

3

4

5

Figure 54.

 Gib bolt tightening sequence.

Содержание G0656























































Отзывы: