Grizzly G0656 Скачать руководство пользователя страница 29

G0656 8" Jointer with Built-In Mobile Base

-25-

To bevel cut on the jointer:

1.

  Read and understand 

SECTION 1: SAFETY

,

 

beginning on 

Page 6

.

2.

  Make  sure  your  stock  has  been  inspected 

for dangerous conditions as described in the 

Stock Inspection & Requirements

 instruc-

tions, beginning on 

Page 21

.

3.

  Set the cutting depth for your operation. (We 

suggest  between 

1

16

"  and 

1

8

"  for  bevel  cut-

ting,  using  a  more  shallow  depth  for  hard 
wood species or for wide stock.)

4.

  Make sure your fence is set to the angle of 

your desired cut.

5.

  If your workpiece is cupped (warped), place 

it so the concave edge is face down on the 
surface of the infeed table. 

6.

  Start the jointer.

7.

  With  a  push  block  in  your  leading  hand 

(

Figure    30

),  press  the  workpiece  against 

the table and fence with firm pressure, and 
feed the workpiece over the cutterhead. 

 

Note:

 

If  your  leading  hand  gets  within  4" 

of  the  cutterhead,  lift  it  up  and  over  the 
cutterhead,  and  place  the  push  block  on 
the  portion  of  the  workpiece  that  is  on  the 
outfeed table. Now, focus your pressure on 
the outfeed end of the workpiece while feed-
ing,  and  repeat  the  same  action  with  your 
trailing  hand  when  it  gets  within  4"  of  the 
cutterhead.  To  keep  your  hands  safe,  DO 
NOT  let  them  get  closer  than  4"  from  the 
cutterhead when it is moving!

8.

  Repeat 

Step 7

 until the angled cut is satis-

factory to your needs.

The  purpose  of  rabbet  cutting  is  to  remove  a 
section  of  the  workpiece  edge  (see 

Figures  32 

&

 

33

).  When  combined  with  another  rabbet  cut 

edge, the rabbet joints create a simple, yet strong 
method of joining stock.

Figure 33.

 Illustration of rabbet cutting effects 

and a few sample joints.

NOTICE

If  you  are  not  experienced  with  a  jointer, 

set  the  depth  of  cut  to  0",  and  practice 

feeding the workpiece across the tables as 

described below. This procedure will better 

prepare you for the actual operation.

Figure 32.

 Typical rabbet cutting operation.

Rabbet Cutting

Содержание G0656























































Отзывы: