Grizzly G0656 Скачать руководство пользователя страница 21

G0656 8" Jointer with Built-In Mobile Base

-17-

Figure 17.

 Dust hose attached to dust port.

Dust Collection

To connect a dust collection hose:

1.

  Install  the  dust  port  as  shown  in

  Figure 

17

,

 

using  the  four  M5-.8  x  16  Phillips  head 

screws and flat washers.

DO NOT operate the Model G0656 without an 

adequate dust collection system. This jointer 

creates  substantial  amounts  of  wood  dust 

while operating. Failure to use a dust collec-

tion system can result in short and long-term 

respiratory illness.

Recommended CFM at Dust Port: 400 CFM

Do not confuse this CFM recommendation with 
the  rating  of  the  dust  collector.  To  determine 
the  CFM  at  the  dust  port,  you  must  consider 
these variables: (1) CFM rating of the dust col-
lector,  (2)  hose  type  and  length  between  the 
dust  collector  and  the  machine,  (3)  number 
of branches or wyes, and (4) amount of other 
open  lines  throughout  the  system.  Explaining 
how to calculate these variables is beyond the 
scope of this manual. Consult an expert or pur-
chase a good dust collection "how-to" book.

2.

  Fit  the  4"  dust  hose  over  the  dust  port,  as 

shown in 

Figure 17

, and secure in place with 

a hose clamp.

3.

  Tug the hose to make sure it does not come 

off. 

Note: 

A  tight  fit  is  necessary  for  proper 

performance.

Figure 18.

 Cutterhead knife at top-dead-center.

��������

������

Setting Outfeed 

Table Height

The outfeed table height MUST be level with the 
knives  when  they  are  at  top-dead-center.  If  the 
outfeed table is set too low, the workpiece will be 
tapered  from  front  to  back.  If  the  outfeed  table 
is set too high, the workpiece will hit the edge of 
the outfeed table during operation, increasing the 
chance of kickback.

To set the outfeed table height:

1.

  DISCONNECT  JOINTER  FROM  POWER 

SOURCE!

2. 

Move the cutterhead guard out of the way or 
remove it, and open the rear access panel. 

3.

  Place  a  straightedge  on  the  outfeed  table 

so  it  extends  over  the  cutterhead

 

and  rotate 

the  cutterhead  pulley  until  one  of  the  knives 
is  at  top-dead-center  (TDC),  as  illustrated  in 

Figure 18

.  

4.

  When  correctly  set,  the  knife  will  just  touch 

the straightedge when the knife is at its high-
est point of rotation, as shown in 

Figure 19

.

Figure 19.

 Using a straightedge to align outfeed 

table height with knife at TDC.

������������

�������

������

Содержание G0656























































Отзывы: