Grizzly G0622 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 48

background image

-22-

Model G0622 (Mfg 2/08+)

6. install the safety bracket and lock it in place

with the pin shown in

figure 25 to keep the

saw from falling.

Note: To ensure the safety bracket fits
securely in the notch on the body frame, the
safety bracket may need to be slightly "modi-
fied" with a hammer or other appropriate
implement to fit securely.

head Locking pin

the head locking pin safely secures the head in
the down position. to ensure the head does not
unexpectedly spring up and tip the bandsaw over,
this locking pin must be properly inserted when
the bandsaw is not in use or before moving it.

To use the head locking pin:

1. diSConneCt BAndSAW FroM poWer!

2. Fully lower the head down, then insert the

locking pin through the holes in the head
pivot arm and base, as shown in

figure 26.

3. Before connecting the machine to power,

remove the locking pin.

figure 26. head locking pin correctly inserted.

head locking pin

The head locking pin secures the head in the

down, horizontal position. you MUST secure

the head with the locking pin before moving

the machine to prevent the head unexpect-

edly springing up causing the machine to tip

or fall. Otherwise, serious personal injury or

property damage could occur.

figure 25. Safety bracket.

Safety Bracket

pin

notch

«
...
22
23
24
25
26
...
»

Содержание G0622

















































Отзывы:

Нет отзывов

Похожие инструкции для G0622

Бренд: Bartell Страницы: 14

EnergySaw-185LCS

Бренд: PEUGEOT Страницы: 32

Бренд: Palmgren Страницы: 28

Бренд: Grizzly Страницы: 88

Бренд: fireStorm Страницы: 5

Бренд: Milwaukee Страницы: 11

Бренд: Ryobi Страницы: 28

Бренд: Hyd-Mech Страницы: 74

Бренд: SawGear Страницы: 32

Бренд: Parkside Страницы: 93

Бренд: Scheppach Страницы: 52

Бренд: Craftex Страницы: 40

Бренд: Worx Страницы: 72

Бренд: Worx Страницы: 132

Бренд: Milwaukee Страницы: 24

Бренд: Sthor Страницы: 88

Бренд: Scheppach Страницы: 90

Бренд: Scheppach Страницы: 144

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды