Grizzly G0622 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 48

background image

-18-

Model G0622 (Mfg 2/08+)

Starting the machine:

1. read the entire instruction manual.

2. Make sure all tools and foreign objects have

been removed from the machine.

3. Connect the bandsaw to power.

4. put on safety glasses and secure loose cloth-

ing or long hair.

5. raise the bandsaw by the handle.

6. Start the bandsaw while keeping your finger

near the on/oFF switch at all times during
the test run (

figure 17). the bandsaw should

run smoothly with little or no vibration.

— if you suspect any problems, immediately

stop the bandsaw and correct before con-
tinuing.

—if you need any help with your bandsaw

call our tech Support at (570) 546-9663.

projectiles thrown from

the machine could cause

serious eye injury. Wear

safety glasses during

assembly and operation.

the  adjustments  listed  below  have  been  per-
formed  at  the  factory.  however,  because  of  the
many  variables  involved  with  shipping,  we  rec-
ommend  that  you  at  least  verify  the  following
adjustments  to  ensure  the  adjustments  remain
unchanged.

Step-by-step instructions on verifying these adjust-
ments can be found in

SECTION 7: SERvICE

ADJUSTMENTS.

factory adjustments that should be verified:

1. Blade tracking (page 34).

2. Squaring the Blade (page 35).

3. Blade guide Bearings (page 36).

Recommended

Adjustments

figure 17. on/oFF switch.

Test Run

«
...
18
19
20
21
22
...
»

Содержание G0622

















































Отзывы:

Нет отзывов

Похожие инструкции для G0622

Бренд: Target Страницы: 40

Бренд: Avid Power Страницы: 16

Бренд: Parkside Страницы: 73

Бренд: HIKOKI Страницы: 112

Бренд: Feider Machines Страницы: 14

Бренд: Axminster Страницы: 26

Бренд: Sammic Страницы: 24

Бренд: Scheppach Страницы: 92

Бренд: Ryobi Страницы: 20

Бренд: Ryobi Страницы: 40

Бренд: ISC Страницы: 70

Бренд: Mitek Страницы: 6

Бренд: KNOVA Страницы: 28

Бренд: KNOVA Страницы: 46

Бренд: Dake Страницы: 34

Бренд: EIBENSTOCK Страницы: 64

Бренд: Meec tools Страницы: 15

Бренд: Meec tools Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды