Grifco GSB-600, Инструкция по эксплуатации

Страница: 2 / 24

2
WARNING
:
Important safety instructions
It is important for the safety of persons to follow all instructions.
SAVE these instructions
WARNING
CAUTION
WARNING
This commercial door operator has been designed and tested to offer safe service provided it is installed, operated, maintained and
tested in strict accordance with the instructions and warnings contained in this manual.
Mechanical
Electrical
When you see these Safety Symbols and Signal Words on the
following pages, they will alert you to the possibility of serious
injury or death if you do not comply with the warnings that
accompany them. The hazard may come from something
mechanical or from electric shock.
When you see this Signal Word on the following pages, it will
alert you to the possibility of damage to your commercial door
and/or the commercial door operator if you do not comply with
the cautionary statements that accompany it.
THESE ARE IMPORTANT SAFETY INSTRUCTIONS. FOLLOW ALL INSTRUCTIONS AS INCORRECT
INSTALLATION CAN LEAD TO SEVERE INJURY OR DEATH
Keep commercial door maintained. Sticking or binding
doors must be repaired. Commercial doors, brackets and
their hardware are under extreme tension and can cause
serious personal injury. Do not attempt to loosen, move or
adjust them. Call for commercial door service. Where applicable, permanently fasten all supplied labels
adjacent to the wall control as a convenient reference and
reminder of safe operating procedures.
Disengage all existing commercial door locks to avoid
damage to commercial door. Install the control (or any
additional push buttons) in a location where the commercial
door is visible during operation . Do not allow children to
operate push button(s) or remote control(s). Serious personal
injury from a closing commercial door may result from misuse
of the opener.
Activate opener only when the door is in full view, free of
obstructions and opener is properly adjusted. No one should
enter or leave the building while the door is in motion.
An electrician must disconnect electric power to the
commercial door opener and control before making repairs or
removing covers.
The actuating member of a biased-off switch is to be located
within direct sight of the door but away from moving parts.
Unless it is key operated, it is to be installed at a minimum
height of 1500mm and not accessible to the public.
Make sure that people who install, maintain or operate the
door follow these instructions. Keep these instructions in a
safe place so that you can refer to them quickly when you
need to.
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play
with the appliance.
If the opener is installed at a height less than 2.5 meters
from floor level or any other level from which the unit can
be accessed (eg mezzanine) the installer is responsible to fit
guards to the opener to prevent access to the chain drive.
Ensure that the temperature range marked on the operator is
suitable for the location. Ensure that entrapment due to the
opening movement of the of the driven part is avoided.
Unbalanced roller shutter doors require a Suitable Anti-
Drop device to catch the door in the event a a failure of
the drive system., such as the GRIFCO GSB-600.
Do not wear rings, watches or loose clothing while
installing or servicing a commercial door opener.
To avoid serious personal injury from entanglement,
remove all ropes connected to the commercial door
before installing the door control.
Installation and wiring must be in compliance with your
local building and electrical codes. Connect the power
supply cord only to properly earthed mains if applicable.
Moisture and water can destroy the electronic components.
Make sure under all circumstances that water moisture or
storage moisture cannot penetrate the electronics. The
same applies for openings and cable entries.
After the installation a final test of the full function of the
system and the full function of the safety devices must
be done.
When operating a biased-off switch, make sure that other
persons are kept away.
The opener cannot be used with a driven part
incorporating a wicket door (unless the opener cannot be
operated with the wicket door open).
Motor may become hot during operation. Appropriate
clearance and/or shielding should be supplied by the
installer to ensure any cabling, wiring and/or other items
cannot come in contact with the motor. If temperature
rise exceeds 50°C all fixed wiring insulation must be
protected, for example, by insulating sleeving having an
appropriate temperature rating.