Grifco GSB-600 Скачать руководство пользователя страница 22

Страница: 22 / 24

MAINTENANCE

Frequently examine the installation for signs of

wear or damage. Do not use if repair or

adjustment is necessary. Power must be turned

off before servicing, cleaning or adjusting the

opener.

Certain mechanical aspects of the installation as

applicable must be checked, see below:

MONTHLY

• Examine the installation for signs of wear or

damage. Do not use if repair or adjustment is

necessary *

• Check chain alignment, tension and condition.

Adjust / replace if required *

• Check PE / IR beam/s and bump edge

functionality where applicable

QUARTERLY

• Check tightness of fixing bolts and (sprocket)

grub screws. Adjust if required *

• Check correct electrical operation

• Check manual operation as per the respective

“Installation and users Manual”

• Lubricate the drive chain *

* SERVICE MUST BE CARRIED OUT BY A

QUALIFIED TECHNICIAN

CHECK DOOR CYCLE COUNT

Door cycle count can only be checked if the

GLMe2L Logic Controller is installed. Limits must

be set.

• Drive door to closed limit

• Press and hold CLOSE for 10 seconds

• After 10 seconds and while still holding

CLOSE, press and release the SET button

• Status LED will light up indicating number of

cycles performed

To read number of cycles, follow the ‘Reading

Status Flashes’ routine described below.

Reading Status Flashes (GLMe2 controllers only)

STATUS indicator will start flashing to signify the

value of the least significant digit of the overall

number. A solidly lit indicator stands for zero.

Press set to view the next digit.

Continue previous step until the STATUS indicator

flashes quickly for 1 second then goes out. This

signifies that the entire number has been

displayed.

To reset error (GLMe2 controllers only)

(This process indicates there has been a severe

problem. Persistent resetting will void warranty

and may damage the door and/or opener). This

procedure will only work when the status light is

flashing 4, 5, 9, 10, 14 or 15 times.

Hold the STOP button for 10 seconds

While still holding the STOP button, press and

release the SET button

The STATUS indicator should flash quickly for 1

second. Any errors that were flashing should have

stopped.

Power MUST be turned off before servicing or adjusting the opener.

Disconnect the supply when cleaning!

WARNING

Содержание GSB-600

























Результаты поиска

Содержание GSB-600

Отзывы:

Бренды по названию

Популярные бренды

Grifco GSB-600, Инструкция по эксплуатации

Результаты поиска

Содержание GSB-600

Отзывы:

Бренды по названию

Популярные бренды