manualshive.com logo in svg

Grifco GSB-600, Инструкция по эксплуатации

Поделиться
Скачать
Grifco GSB-600 Скачать руководство пользователя страница 10

10

INSTALLATION

STEP 1

INSTALL WALL BRACKETS

Install wall Angle, or Wall Brackets, depending on 

the system.

GUD-MK-05: 

1.  Mount Wall Brackets to building using the 3 

slots provided

2.  Install both sides at the same height. 

GUD-MK-07: 

1.  Mount wall Angle to building using the 4 slots 

provided, for flexibility of install the angle can 

be mounted with the slots towards or away 

from the opening.

2.  Install both sides at the same height.

3.  Install the end plates using the M16 fasteners 

supplied (Torque 190Nm—210Nm)

NOTE: Safety brake side, End Plate must be 

outside of wall angle as shown below

STEP 2

INSTALL DOOR DRUM

Install door drum into the bracket slot and position 

at the correct centre distance from wall. U-Drive 

mounting brackets feature positional rebates to 

allow for easy alignment.

STEP 3

INSTALL FLANGE BEARING

Slide the flange bearing over the end of the shaft 

and use the M16 fasteners supplied. 

(Torque 190Nm—210Nm)

 180 

 236 

 180 

 292 

 180 

 236 

 180 

 292 

 180 

 236 

 180 

 292 

 180 

 236 

 180 

 292 

NOTE: Method of mounting wall brackets to the building structure is 
dependent on the type and integrity of the wall/structure.

The installer must carefully assess the structure and suitably engineer 
a mounting method to ensure robust and safe installation.

Содержание GSB-600

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды